|
|
|
|
|
|
Their flexibility and fast heating feature make it necessary to use the Armagnac in premises such as :
- Sales and/or storage areas
- Sports hall
- Agriculture and breeding premises
- Industrial and commercial buildings.
Over a pleasant presentation, electric aerothem Armagnac are fitted with all components and accessories allowing a quick installation, a safe and quiet operation.
- Armoured resistance
- Slow speed helicoid fan
- Power contactor
- Safety and control thermostats
- Fan timer
- On/off switch with light signal
- White RAL 9003 painted sheet steel frame, RAL 9010 lacquered deflectors protected with a removable plastic film.
Produced in 2 sizes, for power from 6 to 24 kW.
For powers from 15 kW to 24 kW only, the equipment is fitted with contactors allowing a two step operation if necessary.
CAUTION :
The proper operation of the aerotherm depends on a correct installation and start-up.
Aerotherm should not be installed in :
• Hazardous areas
• Premises containing vapours of chlorinated combination
• Areas with high contents of inflammable dusts
• Highly humid rooms
|
|
AIRCALO is the french company leader in production of gas heaters.
These equipment may be connected either with vertical or horizontal vent or through a chimney.
These aerotherms do meet the main requirements of the CE standards requirement related to gas-fired aerotherm.
CAUTION :
These equipment can only be used in sufficiently aerated premises, except where a tight connection is provided.
The proper operation of the aerotherm depends on a correct installation and start-up.
Aerotherm should not be installed in :
- Hazardous areas
- Premises containing vapours of chlorinated combination
- Areas with high contents of inflammable dusts
- Highly humid rooms.
|
|
The range of helicoid aerotherm consists in 7 different models used either in heating or cooling mode.
These equipment are intended to large volume buildings, store house, garage, workshop…
Aircalo aerotherm enables rapid heating or cooling volumes at the same time, mixing the air sufficiently to prevent its stratification (it is possible to complete this mixing by using zephir air recyclers).
Depending upon the characteristics of the building to be equipped, the Aircalo aerotherm may be hung (vertical blowing) or wall mounted (horizontal blowing).
|
|
|
Bi-energy reversible monosplit system for industrial or commercial buildings : Internal unit is double skin 25 mm thickness including stainless steel exchanger with gas fired burner 35 kW for heating and R410A coil working with an external unit air/air 17 kW for cooling. 2 speeds fan for direct blowing or ducted applications. The unit is supplied complete with fume kit and regulation box. (Automatic change over gas heating / electrical cooling).
|
|
|
The ceiling mounted ELEGANT unit heaters are especially suitable for heating and/or cooling rooms with low ceilings, such as shops, workshops, garages and supermarkets. There are 10 models with heating only and 5 models with cooling operation, each with three-speed motors, continuous speed variation upon request, numerous controls and accessories for the perfect control of the ambient temperature.
|
|
The air heaters in series TopWing have a modern, attractive design, the harmonious, soft outline of which is shown to its best advantage in showrooms, entrance halls, sales floors, or supermarkets. The light colour in white RAL 9016 and the rounded edges let the TopWing device
blend in on ceilings.
|
|
There are 4 models available, to suit the needs of the application ranging from 2 - 30 kW.
- Variable room heaters, to be used transportable and stationary.
- Air intake fan heaters.
- Ventilation air heaters for air intake, circulation and mixed air.
- Built-in units with heaters and fan
|
|
Unit heater LH for mixed air and return air modes for wall-mounting or ceiling mounting.
Casing welded, galvanised sectional steel frame. Casing panels galvanised; paint finish available on request.
Discharge louvre with manually adjustable guide vanes.
Axial fan for quiet operation, with statically and dynamically balanced impeller and protection grille.
Three phase motor 3 x 400 V, 50 Hz; degree of protection IP 54, insulation class F; two-speed, high/low speed with ∆/Y; low-noise level, maintenance-free, direct-drive, with amply dimensioned ball bearings and special grease filling for wide temperature spread, insulation class F, terminal box, motor protection by thermo contacts in the windings in conjunction with a single-stage/multi-stage switch or automatic controller.
|
|
The heaters of the IGRAF family are used for surface heating and for fluid heating.
•HEATING AND DRYING of marble slabs, of resin surfaces, of scrap iron.
•Suitable to be incorporated in all exsiccation and drying ovens for wood and other materials.
•HEATING OF FLUIDS for industrial degreasing, for food cooking.
|
|
|
The Atlas unit heaters have a big heart: a coil that has been conceived, designed and manufactured specifically for heating industrial environments. The thickness of the pipes, steel as standard, the diameter (Ø 22 mm) and the excellent ratio between the flow-rate of air and the heat output guarantee long life and exceptional comfort. The Atlas unit heaters are made in 10 sizes, with heat outputs from 5 to 120 kW, and are available with 1 row coils for steam or high-temperature water systems, 2 row coils for hot water systems and 3 row coils for low-temperature hot water systems. They can be installed on the wall and on the ceiling.
|
|
|
The HELIOS unit heaters, built with the same criteria of sturdiness and safety that define all Sabiana products, stand out for the splendid new design of the casing, made using anodised aluminium bars and polished die-cast corners. They have the same big heart as the Atlas unit heaters: a coil that has been conceived, designed and manufactured specifically for heating industrial environments. The thickness of the pipes, steel as standard, the diameter (Ø 22 mm) and the excellent ratio between the flow-rate of air and the heat output guarantee long life and exceptional comfort.
|
|
|
To provide fan assisted heating to commercial or industrial environments, or for drying applications.
|
|
VARMY: back up heater Heat 2 in 1:
Use energy absorptive to produce double heat!
- double reflectors stainless, high-output system erasing (IRM)
- Internal Plates leading heat, diffusion by convection
- structure interns out of aluminum
- safety device: decontaminate the apparatus in the event of fall
- power: 500 with 2000W/h
- height 630mm, 9 kg
|
|
| ... products without information |
| |
|
|
see the results for the following category : 
