|
|
3 or 4 baking chambers
From 1 to 3 doors by chamber
Baking surface for 3 chambers : from 2.5 m² to 14 m²
Baking surface for 4 chambers : from 3.3 m² to 18 m²
2 chamber heights : 23 cm or 26 cm
Energy : electricty
Independent electronic control panel for each chamber
Energy saving system
Alarm system
Rockwool insulation
Refractory bricks 25 mm
Baking chamber lit up by 12 V iodine lamp
Central steamer independent for each chamber
Voltage : TRI – 380 V – 50/60 Hz +N+T
Many combinations, please consult us for more information.
|
|
|
For the artisan baker, Doyon offers the best choice for baking old-world artisan style crusty breads with a thick and crispy crust but still soft inside. Our modular ovens offer perfect heat distribution and our outstanding steam injection system gives you complete control over your oven chamber. Doyon artisan ovens are quick and easy to install and are the perfect choice for a variety of quality hearth breads, pastries, cookies, pies, cakes, pizzas, roasts, fast foods and much more.
|
|
4 Models : 2 or 3 independent decks
2 or 4 trays 600 x400 mm per deck
Energy: electricity
Electromechanical control
Steam generator on each deck
Independant control of the sole and the ceiling
Temperature : from 20 °C to 300 °C
Timer
1 air inlet per deck
Canopy
Glass window
Ergonomic handle
Refractory plates assuring a perfectly soft and regular baking
Light on each deck
OPTIONS
- Support with castors
- Proover with glass doors and castors (from 20°C to 60°C)
- Proover with glass door, castors and steam generator (from 20°C to 60°C)
|
|
1 to 4 decks
4 module heights on choice (to be combined according to need) from 320mm to 470mm
Deck capacity : from 1 to 6 trays 600 x 400
Energy : electricity
Energy saving system
Independent control for the sole, the ceiling and the door temperature
Electromecanic or digital control panel
Ceramic floor plates
Glass door
Light
1 inlet for each level
OPTIONS:
Steaming system
Proover
Support
Canopy
Many combinations, please consult us for more information.
|
|
|
|
|
|
Category: Serie 2000
Model: SE/99/2
Code: 04676.. x 2 + WPC8010
SERIE 2000
The SERIE 2000 ovens are particularly suited to bake pizzas on firestone or in baking-pans. SERIE 2000 is available in two versions: with electronic control board (E) or with electromechanical control board; both versions are available with stainless steel front or with enamelled front. The baking chambers are entirely made of AISI 430 stainless steel and the baking surface is of modular firestone; the doors show large ceramic glass to get a complete inspection of the inside. The single chambers can be overlapped up to three units, each of them independent for their control elements and relevant supply. A double testing makes these ovens particularly reliable, while the safety conditions are assured by a safety thermostat, calibrated at 450°C (rechargeable). A smoke suction valve is also an important feature of the ovens belonging to SERIE 2000, the valve opening can be adjusted according to the work. The baking module can be completed by optional supply of a support or cell, which can be heated or neutral (with stainless steel front-side). Moreover, on the module, a stainless steel suction hood equipped with motor and speed changing gear can be mounted.
|
|
Chicago-style pizzas, hearth-style breads—Baxter Deck Ovens are perfect for any product where the crust is king. The combination of specially designed heating elements and high-quality, atmospheric steam means you get exactly the finish you want, from a thick, chewy pizza slice to a flaky, crispy loaf of artisan bread.
Quick Facts:
- Reinforced 5/8"-thick stone allows temperatures as high as 550˚F
- Independent settings to heat top and bottom of each deck separately
- Each deck operates independently
- For crisper crusts, steam is standard
|
|
Deck ovens Omega - Electric
Capacity
• Baking area : from 4,5 to 19,7 m²
• Useful height on each deck : 185 mm
• Useful height on top deck : 235 mm
• Number of decks : 3, 4 or 5
• Doors of 600 or 800 mm
• Number of door : 1 or 2 per deck
Characteristics
• Electrical top deck with independent regulation
deck / roof (vault)
• Optional electronic control Opticom on each deck
• Reversible control panel on the right or left hand side
• Door with reversible right or left handle
• Fitted oven on one side and at the back
• Optional steam vents on top deck or on each deck
• Stainless steel bench (for 3 or 4 deck oven)
• Optional integrated lifter (see integrated lifter)
• Optional loader-unloader
|
|
Adamatic Model ADO-2 Deck Oven
Standard Features:
- Modular fully insulated deck design
- Two pan wide capacity
- One to four decks in height
- Each deck independently operated
- Double glazed full width/height viewing...
|
|
Our DXc Deck Oven features a large, full colour graphics Colour Controller to each deck and a revolutionary steaming system. This is combined with an unbeatable reputation for technological sophistication, high performance and reliability.
Top Features
* Full graphics, programmable, electronic control system
* Fast heat up and recovery
* Revolutionary new low energy steam system
|
|
Mabo produces this tile in a large range of heights to satisfy all kinds of demand, as regards the capacity lead and the fire resistance.
The TT tile is used to cover great lengths (up to 24 m) of industrial or commercial buildings or mono or multi-storey car parks. This tile is formed by two variable height legs taking the prestressing reinforcement and the eventual loose reinforcement and a reinforced concrete slab with a thickness of 5 cm, a width of 2,5 m and a variable length.
The TT tile is erected upon L or T shaped beams with a distance extrados beam - extrados lower flaps like the tile height. So, once erected, the tile produces with the extrados of the floor holder beams an uninterrupted plane ready for the composite casting.
|
|
|
|
|
|
Our range of double tee units is the most structurally efficient system available for long-span, higher-load flooring applications. It's easy to use, flexible to work with and offers major time savings.
Double tee beams benefits
- Simple to install
- Limited site labour
- Spans in excess of 20m can be achieved
- Creates large areas of uninterrupted floor space free from column obstructions
- Reduced frame costs due to lower floor weight
- Allows flexibility in the building for changes of use
- High strength quality concrete requires minimum maintenance
- Savings in the cost of supporting structure and foundations
- Up to 4 hours fire resistance
- Can be used without suspended ceilings for aesthetic appeal
- Early access to floor areas for finishing subtrades
- No propping required
- Regular deliveries during working day or night
- Numerous advantages over alternative forms of construction
- Thermal mass efficiency of double tees means it can be used alongside Thermocast
Double tee beams applications
Long span roofs
Long span ceilings
Long span floors
When screeded, can be used in car parks
Unscreeded, the units are suitable for lower car parking decks
Applications where raised floor finishes are required
Double tees can be used as internal or external wall units for architectural purposes
|
|
The Pegaso structural system%u2019s main feature is a plane prestressed reinforced concrete slab with an open edge and diminishing in cross-section. The Pegaso slab is combined with pillars (including PVC rainwater down-pipes and overhead travelling crane bracket if needed), TH ground beams and closing gables.
The Pegaso slab diminishing in cross-section allows water to flow through the external edges, thus bypassing the construction of inside building sewer and drainage systems; in the event of extraordinary rainfalls the extrados shape and width allow a remarkable storage capacity and a fast draining of waters.
|
|
The Zephir structural system is the latest and most developed output of the company%u2019s production research path; Zephir consists of microshed slabs, plane ground beams and closing reinforced concrete or sandwich gables.
The Zephir system was developed by our Precast Division in cooperation with the Faculty of Engineering in Parma, Italy: the output is a prestressed reinforced concrete element used in the roofing of wide surface areas; it has excellent technical and functional features and a high architectural value.
Its tubular section provides the product with a remarkable traverse camber stiffness, which envisages long-term window frame duration, while the wide surface base guarantees high stability and makes it particularly safe during installation.
Thanks to its high storage capacity and its shape, water, however abundant, flows naturally rapidly and effectively on it.
|
|
The Argo structural system consists of a plane prestressed reinforced concrete slab with an open end; the slab is combined with pillars (including PVC rainwater down-pipes and overhead travelling crane bracket if needed), prestressed reinforced concrete %u201CTH%u201D ground beams, closing gables
The Argo diminishing cross-section allows water to flow on the external edges, thus bypassing the construction of inside building sewer and drainage systems; in the event of extraordinary rainfalls the extrados shape and width allow a remarkable storage capacity and a fast draining of waters.
|
|
|
|
|
|
This is the fruit of the constant commitment of Mabo in the research of new solution for prefabricated construction.Euroalares is a revolutionary roofing-tile, as a new interpretation of a well-known shape conjugating the transportability and the possibility of stacking with the lightness primary exigencies. The long study of the shape, investigating the morphologies that are far from the classic pre-assembled civil engineering, gives high level visual and plastic results, reminding the regularity of the arched multiple-spans and the contemporary realizations of the organic architecture.
description
Euroalares is revolutionary as regards its design, and all the aspects of the plant manufacture and manufacturing process.
We can see clearly in the tile a supporting and a supported part.
The main framework is constituted by two lateral arches in reinforced concrete, preassembled to the transversal little beams, to the supports and to the rectilinear and longitudinal chain placed in the centre line.
This main framework is braced suitably, inside the surface created amongst the arch, the chain and the transversal little beams. The surface of the tile is realized in light concrete; the material used combines a high fire resistance and a high insulating power, so this high performance element can assure a great thermal comfort without any following insulating manufacture.
|
|
Concrete roof elements (Double T units) are mainly used in residential construction and long span industrial and commercial buildings, such as sport halls. The Consolis Group produces two main types of elements: namely ribbed lightweight roof units and hollow-core slabs. These components are usually prestressed.
The main features of the elements are:
* Light weight due to slender cross-sections
* Large spans
* Smooth soffit
* Easy and quick to install
|
|
|
|
|
|
The natural evolution of the system building is going over the role played till now, a simple executor of structures that must be covered and visible only after a second project phase of "adjustment". The ambition of the system building is to consider all the level of use of a building, to shape itself according to the natural light, the plant engineering and all the climatic requirements
description
The roofing-tile president has an "omega-shaped" cross section, where the vertical walls rise from the extrados to create a great natural drain of storm water. They have a swelling in the lower parts for an excellent spread of the prestressing reinforcement, a natural good support for any eventual ceiling element and a hidden platform for little cable ducts or fixing for eventual cases to place in the tile intrados. The finishing is semi washable white paint varnish on basis of aqueous anion resin.
Each tile is insulated in the extrados placing an insulating board on the slab; the waterproofing is realized through alluzinc plates fixed through an automatic stapling machine assuring a perfect sealing of the superimpositions.
The breadth of the flat surface offers many possibilities for a good practicability and sitting plants and machinery.
Some insulating ceiling plates are placed between the tiles and are surmounted by some cover slabs. This interspace represents an airing room with effect "cold roof" involving many good effects with regard to the interior thermal comfort.
|
|
| ... products without information |
| |
|
|
see the results for the following category : 
