|
|
Concrete Waxed Cast Interior Ground.... Autolissant, it makes it possible to carry out one finished with the aspect of a smoothed cover tinted in the mass or patinated with the pigments powders in a workshop spirit of artist.
Ideal for large surfaces, it allows the fast realization of interior grounds.
Of fluid consistency, it can be cast on a thickness of 4 à10 Misters Produit line entry, his implementation must be meticulous to avoid the occasional phenomenon of microscopic cracks.
It makes it possible to work on supports usual cements and in restoration on an existing tile.
Slightly sandpapered it will be then protected to guarantee its durability by one from our products of completion.
From 27 euros/m ² including all taxes (except protector)
|
|
Concrete Waxed Cast Interior Ground.... Autolissant, it makes it possible to carry out one finished with the aspect of a smoothed cover tinted in the mass or patinated with the pigments powders in a workshop spirit of artist.
Ideal for large surfaces, it allows the fast realization of interior grounds.
Of fluid consistency, it can be cast on a thickness of 4 à10 Misters Produit line entry, his implementation must be meticulous to avoid the occasional phenomenon of microscopic cracks.
It makes it possible to work on supports usual cements and in restoration on an existing tile.
Slightly sandpapered it will be then protected to guarantee its durability by one from our products of completion.
From 27 euros/m ² including all taxes (except protector)
|
|
Concrete Waxed Cast Interior Ground.... Autolissant, it makes it possible to carry out one finished with the aspect of a smoothed cover tinted in the mass or patinated with the pigments powders in a workshop spirit of artist.
Ideal for large surfaces, it allows the fast realization of interior grounds.
Of fluid consistency, it can be cast on a thickness of 4 à10 Misters Produit line entry, his implementation must be meticulous to avoid the occasional phenomenon of microscopic cracks.
It makes it possible to work on supports usual cements and in restoration on an existing tile.
Slightly sandpapered it will be then protected to guarantee its durability by one from our products of completion.
From 27 euros/m ² including all taxes (except protector)
|
|
Our best seller, the FS-Series Panel system, is constructed of a welded structural steel assembly designed to accommodate ultimate and dynamic loads. Its specially formulated cementitious fill and powder coated epoxy finish give the FS panel a quiet and very solid feel underfoot. Panel systems are
available in both 24" x 24" and 600mm x 600mm.
|
|
The S-Series hollow steel panel system uses the same welded steel technology found in the FS panel. With its high strength and light weight, the S-Series panel is the product of choice for many computer room applications. This panel has the ability to interchange with the FS panel, allowing for ultimate flexibility in flooring design.
Panel systems are available in both 24" x 24" and 600mm x 600mm.
|
|
| ... products without information |
| |
|
The RECTOR I beams are made of prestressed concrete, with or without end strut. They support the purlins and are used to transfer the stress onto the columns. They can be of constant inertia or variable along the height.
|
|
| ... products without information |
| |
Almost all our standard cross sections can be used for BRESPA® Ventilation Floors. The principle is simple yet brilliant: the voids are coated and used as aeration channels. Exhaust and fresh air valves are placed directly into the soffit of the floors. Additional aeration channels for lateral distribution are therefore not required below the ceilings. Room and building heights can be reduced.
It is important to decide early for the application of BRESPA® Ventilation Floors, to use these ceilings soon, because this will influence positively a multitude of decisions for other areas of your building.
|
|
|
Solai carries out the calculation and the design of solai precast concrete slabs or jetties in work. For the dimensioning it uses the method of the permissible tensions and the state limit. For the s.l they can be adopted the verification criteria according to DM 96, EC2/92, EC2/05, NTC 2008.
|
|
|
|
|
|
SAFE is the ultimate tool for designing concrete floor and foundation systems. From framing layout all the way through to detail drawing production, SAFE integrates every aspect of the engineering design process in one easy and intuitive environment. SAFE provides unmatched benefits to the engineer with its truly unique combination of power, comprehensive capabilities, and ease-of-use.
Laying out models is quick and efficient with the sophisticated drawing tools, or use one of the import options to bring in data from CAD, spreadsheet, or database programs. Slabs or foundations can be of any shape, and can include edges shaped with circular and spline curves.
Post-tensioning may be included in both slabs and beams to balance a percentage of the self-weight. Suspended slabs can include flat, two-way, waffle, and ribbed framing systems. Models can have columns, braces, walls, and ramps connected from the floors above and below. Walls can be modeled as either straight or curved.
Mats and foundations can include nonlinear uplift from the soil springs, and a nonlinear cracked analysis is available for slabs. Generating pattern surface loads is easily done by SAFE with an automated option. Design strips can be generated by SAFE or drawn in a completely arbitrary manner by the user, with complete control provided for locating and sizing the calculated reinforcement. Finite element design without strips is also available and useful for slabs with complex geometries.
|
|
Format: 3050 x 1300 mm
Thickness: 0.9, 1.2, 1.5, 1.8, 2, 3 mm
NOTE
Sizes and thickness of Arpa standard production program. Please contact Arpa commercial dept for custom specifications.
|
|
|
|
