|
|
|
Piano Wall™ combines a precast retaining wall and safety barrier in a single engineered unit. This unique solution was developed for projects that require a five- to ten-foot-high-reinforced earth wall incorporating a traffic barrier. The use of Piano Wall speeds up highway construction and reduces cost on projects requiring low-grade separation between opposite roadways or between a roadway and the adjacent non-traveled area. Installation rates of Piano Wall average 170 linear feet of barrier and 1,700 square feet of Reinforced Earth retaining wall per day. Piano Wall provides a seamless transition to higher reinforced Earth walls or abutments being constructed on the same project
|
|
|
TechWall® is a precast counterfort retaining wall system. TechWall retaining walls are an effective solution when site conditions preclude the use of reinforcing strips such as severe right-of-way restrictions, utility conflicts, pile foundations and roadway widening. Unlike conventional cast-in-place concrete structures, TechWall combines the inherent advantages of a precast concrete system with the traditional benefits of a counterfort design. Construction follows a simple, rapid and predictable method. Precast panels are placed atop a cast-in-place shear key, a footing is poured on top of the key, and structure backfill is placed and compacted. This unique system saves cost and construction time.
|
|
Designed to provide a cost-effective, versatile solution for a wide variety of earth retention and material storage uses, Tarmac Precast's retaining wall units are available in a range of standard, 1m wide units, from 1m to 3.75m high.
Technical information:
- Designed for specific loading conditions
- Simple, rapidly installed dry construction
- Easy to handle, using minimal labour
- Makes full use of available land
- Loading on either or both faces
- High-quality factory production
- Improved efficiency of stock yards and factories
- Easily demounted and reused
- Has a wide variety of uses
|
|
Veil supporting height 1 m for sealing in sole concrete realized on the building site.
Stone front face proposed in 3 colors: dark, gray gray clearly and ocher.
|
|
|
|
|
|
Process RENFOTER MODULE® allows the realization of retaining walls in solid mass reinforced reinforced concrete facing.
It concerns the technique of the reinforcement of the grounds by not very extensible and flexible reinforcements (Standards NF P 94220-0 and 2) and of the recommendations and code of practice "the works out of reinforced earth".
The wall in reinforced ground is consisted of association:
- of a facing of modules prefabricated out of reinforced concrete any height or superposable,
- of a solid mass of fill set up by layers,
- reinforcements connected to the facing and narrowly overlapping in the embankment.
The facing is made of juxtaposed and superimposed rectangular modules.
The heights of the modules are adapted to the project.
The aspect of the facing is studied with the request: gray concrete smoothes, brushed, sanded, stamped concrete (standard matrix hones, rock,...), tinted concrete and other architectural treatments.
The reinforcements are out of hot galvanized steel fabrics, of form and size adapted to each project.
Fields of application: current retaining walls, carrying abutments, walls out of cut, walls staged.
Advantages:
- Adaptability with the poor subgrades thanks to the flexibility of its facing,
- Increased Security: the modules out of reinforced concrete and are ribbed
- Speed of implementation
- Economy: simplicity of implementation, current filling material, in the respect of the Recommendations of Setra.
|
|
|
Retaining walls in L or T (series 300 and 600 particularly adapted to the déchèteries), length 2,00 m, 2,5m, 3,00m with 6,00m and height 1,20 m with 2,75 Mr. Pose faster, more esthetic (less unite)
|
|
|
Retaining walls in L or T, standard length in 1,25 or 2,50 m and height 2,50 m with 8,00 Mr.
|
|
JUMA Beton is the specialist in the manufacture of WORK OF PRECISION out of precasted concrete.
JUMA Beton produces all kinds of work of precision out of concrete smoothes, gray and this as well for the industrial premises, nonresidential construction, residential construction like for the construction of roads.
|
|
|
Retaining walls in L or T, standard length in 1,25 or 2,50 m and height 2,50 m with 8,00 Mr.
|
|
| ... products without information |
| |
|
Piano Wall™ combines a precast retaining wall and safety barrier in a single engineered unit. This unique solution was developed for projects that require a five- to ten-foot-high-reinforced earth wall incorporating a traffic barrier. The use of Piano Wall speeds up highway construction and reduces cost on projects requiring low-grade separation between opposite roadways or between a roadway and the adjacent non-traveled area. Installation rates of Piano Wall average 170 linear feet of barrier and 1,700 square feet of Reinforced Earth retaining wall per day. Piano Wall provides a seamless transition to higher reinforced Earth walls or abutments being constructed on the same project
|
|
|
TechWall® is a precast counterfort retaining wall system. TechWall retaining walls are an effective solution when site conditions preclude the use of reinforcing strips such as severe right-of-way restrictions, utility conflicts, pile foundations and roadway widening. Unlike conventional cast-in-place concrete structures, TechWall combines the inherent advantages of a precast concrete system with the traditional benefits of a counterfort design. Construction follows a simple, rapid and predictable method. Precast panels are placed atop a cast-in-place shear key, a footing is poured on top of the key, and structure backfill is placed and compacted. This unique system saves cost and construction time.
|
|
Designed to provide a cost-effective, versatile solution for a wide variety of earth retention and material storage uses, Tarmac Precast's retaining wall units are available in a range of standard, 1m wide units, from 1m to 3.75m high.
Technical information:
- Designed for specific loading conditions
- Simple, rapidly installed dry construction
- Easy to handle, using minimal labour
- Makes full use of available land
- Loading on either or both faces
- High-quality factory production
- Improved efficiency of stock yards and factories
- Easily demounted and reused
- Has a wide variety of uses
|
|
Veil supporting height 1 m for sealing in sole concrete realized on the building site.
Stone front face proposed in 3 colors: dark, gray gray clearly and ocher.
|
|
|
|
|
|
Process RENFOTER MODULE® allows the realization of retaining walls in solid mass reinforced reinforced concrete facing.
It concerns the technique of the reinforcement of the grounds by not very extensible and flexible reinforcements (Standards NF P 94220-0 and 2) and of the recommendations and code of practice "the works out of reinforced earth".
The wall in reinforced ground is consisted of association:
- of a facing of modules prefabricated out of reinforced concrete any height or superposable,
- of a solid mass of fill set up by layers,
- reinforcements connected to the facing and narrowly overlapping in the embankment.
The facing is made of juxtaposed and superimposed rectangular modules.
The heights of the modules are adapted to the project.
The aspect of the facing is studied with the request: gray concrete smoothes, brushed, sanded, stamped concrete (standard matrix hones, rock,...), tinted concrete and other architectural treatments.
The reinforcements are out of hot galvanized steel fabrics, of form and size adapted to each project.
Fields of application: current retaining walls, carrying abutments, walls out of cut, walls staged.
Advantages:
- Adaptability with the poor subgrades thanks to the flexibility of its facing,
- Increased Security: the modules out of reinforced concrete and are ribbed
- Speed of implementation
- Economy: simplicity of implementation, current filling material, in the respect of the Recommendations of Setra.
|
|
|
Retaining walls in L or T (series 300 and 600 particularly adapted to the déchèteries), length 2,00 m, 2,5m, 3,00m with 6,00m and height 1,20 m with 2,75 Mr. Pose faster, more esthetic (less unite)
|
|
|
Retaining walls in L or T, standard length in 1,25 or 2,50 m and height 2,50 m with 8,00 Mr.
|
|
JUMA Beton is the specialist in the manufacture of WORK OF PRECISION out of precasted concrete.
JUMA Beton produces all kinds of work of precision out of concrete smoothes, gray and this as well for the industrial premises, nonresidential construction, residential construction like for the construction of roads.
|
|
|
Retaining walls in L or T, standard length in 1,25 or 2,50 m and height 2,50 m with 8,00 Mr.
|
|
| ... products without information |
| |
|
EverLoc™ Retaining Walls are also available without the dress joint! The Full Series offers a more conventional appearance while maintaining the key features EverLoc™ is known for. This unit can be used by itself or mixed with the Traditional Series to increase the randomness of your EverLoc™ Wall.
|
|
|
The 805T serves two purposes. First, it is used with corners to provide proper bonding for 810T units. By placing one 805T beside a corner unit on each course, the need for sawing at corners is eliminated (for walls with one outside corner), efficiency is increased, and installation costs are reduced. Secondly, the 805T is used to maintain bond throughout a radius (without sawing).
|
|
|
The 810T is the original EverLoc™! It is a lightweight, one-square foot unit giving EverLoc™ its unique appearance. The unit has an off-set dress joint creating a multi-size or random effect. Radius edges on three sides give EverLoc™ a softer, tumbled look while allowing for aesthetically pleasing inside and outside radius walls. A unique lug and groove locking mechanism makes EverLoc™ one of the most user-friendly srw's on the market today. The locking mechanism, also, prevents the units from opening throughout radius walls to expose aggregate. 810T's can be used by themselves or mixed with 810F's. Simply mixing both styles increases randomness by introducing a third size
|
|
|
|
