|
|
|
Thanks to the Tank-in-Tank technology, ACV combined water heaters are high performance water heaters that can also provide heating. These units are selected by our customers in more than 40 countries situated at all latitudes, from Siberia (outside temperatures as low as – -65°C) to Mexico and the Persian Gulf (outside temperatures over 50°C).
|
|
Since the selection of materials until the packing of the products, these water-heaters are manufactured according to the most modern processes and undergo a battery of test which ensure an exceptional output and a reliability to them. These water-heaters of a greater capacity, namely from 200 to 300 liters, offer warm water to profusion for the large-scale consumers. They are posed imperatively on the ground or in a wall cupboard, one tightens, a storeroom or a wash-house.
Installation
Hydraulic connection
3/4 " (20x27) for the apparatuses from 200 to 300 L.
The water-heaters must imperatively be installed with a group of security in conformity with standard NF D 36-401.
If the water supply is with a pressure higher than 5 bars, a pressure regulator must be assembled upstream group of security.
Electric connection
Electric connection must be carried out by rigid driver in a fixed drain in accordance with standard NF C 15-100. Earthing is obligatory.
Fixing
The ground intended to receive the hot-water heater must be carefully checked before carrying out sufficient sealing (mini Ø 12 mm) to support the load of the hot-water heater which represents approximately the double of its capacity.
|
|
BGV, balloon ECS suction cup
CHARACTERISTICS
Balloon medical Gas warm water of tertiary, domestic and industrial use, with suction cup, from 253 to 309 liters
Tertiary range ground
Ferment thermovitrifiée
2 or 4 magnesium anodes according to the model
Sheet jacket (MO)
Insulation foams polyurethane 50 mm (without CFC)
2 inspection doors (Ø 130 mm)
Atmospheric burner with stainless steel slope
Electronic ignition and intermittent night light
Pallet fixes out of steel high-gauge
Articulated column including/understanding 4 aquastats: antifreeze, regulation, overheating and safety
Drain large diameter (1 "1/2) allowing a facility of cleaning
Valve of safety of 7 bars (included)
Connection and emptying device to a loop of circulation (included)
Regulated out of Natural gas with small pocket of transformation for Butane/Propane
Evacuation (maximum length = 7 meters)
- Model with horizontal concentric suction cup for mural exit
- Model with vertical concentric suction cup for exit roof
Kit mural suction cup (standard), or roof (to specify with the order)
Guarantee: 3 years on the tank, 1 year on the parts.
|
|
Since the selection of materials until the packing of the products, these water-heaters are manufactured according to the most modern processes and undergo a battery of test which ensure an exceptional output and a reliability to them. The water-heaters of the ranges Compact and Standard are fixed vertically at the wall.
The Compact range proposes immersion heaters of a capacity from 15 to 30 liters for the second distant drawing up. The water-heaters of 15 liters, available in two models, can be fixed above or below the sink.
The Standard range with water-heaters of a capacity from 50 to 200 liters proposes for each apparatus two specimens which differ by their resistances. The choice of resistance used must be done according to the nature of the water of the area. To equal effectiveness, a resistance steatite is adapted better to water limestones than a standard resistance immersion heater.
Installation
Hydraulic connection
1/2 " (15x21) for the apparatuses from 15 to 50 L.
3/4 " (20x27) for the apparatuses from 75 to 200 L.
The water-heaters must imperatively be installed with a group of security in conformity with standard NF D 36-401.
If the water supply is with a pressure higher than 5 bars, a pressure regulator must be assembled upstream group of security.
Electric connection
Electric connection must be carried out by rigid driver in a fixed drain in accordance with standard NF C 15-100. Earthing is obligatory.
Fixing
The wall intended to receive the hot-water heater must be carefully checked before carrying out sufficient sealing (mini Ø 12 mm) to support
|
|
CHARACTERISTICS
From 50 to 200 liters, a range of water-heater of compactness. They
fix imperatively at the wall, a tripod of support which can be added according to
type of partition.
Ferment out of vitrified steel assembled by automat of welding guarantees of a perfect and durable sealing.
The oversize magnesium anode reinforces the anti-corrosive protection of the unit.
Mono 230 V or all currents
Ferment guarantee 5 years, guaranteed parts 1 year
|
|
| ... products without information |
| |
|
|
see the results for the following category
