|
|
Expanded polystyrene panel of strong density on right board. This PSE is of color silver plated gray.
Panel in PSE of strong density on right, gray board silver plated. EPSISOL gets busy for the insulation of the grounds of the apartment buildings, tertiary sectors and of the establishments receiving of the public. It is intended for the thermo isolation:
- under-face of the quay levels of houses,
- under cover of the floors located in top of basement, on underfloor space, external passage or quay level,
- floors (low or intermediaries) heating with warm water low temperature, reversible and radiant electric.
|
|
|
|
|
|
Springvale Floorshield has been providing the effective, efficient and cost-effective solution to insulating a wide variety of solid and suspended floor constructions for decades, making substantial contributions to energy efficiency.
An expanded polystyrene rigid insulation board, it is available in original white EPS or as Platinum, to provide even higher insulation values.
Platinum Floorshield is an EPS board which incorporates a graphite component called Neopor®, manufactured by BASF, to provide significantly improved thermal insulation performance, for example, to achieve higher levels of the Code for Sustainable Homes or just to improve SAP ratings.
Floorshield products are light and easy-to-handle and can be fitted simply in domestic, commercial and industrial ground floor applications. Floorshield is suitable for use in solid concrete floors above or below the ground bearing slab; above a suspended beam and block floor; within a suspended timber floor and below under floor heating systems.
The inherent insulation and compressive strength properties of this versatile material make it the most cost-effective loadbearing insulant for floor construction, with a compressive strength at 1% compression of 21 kPa. Springvale Floorshield products are the ideal solution for domestic applications.
Providing excellent thermal insulation properties, Floorshield and Platinum Floorshield reduce heat loss, conserve energy and can be used in conjunction with other products in Springvale%u2019s Shield range to assist compliance with the Code for Sustainable Homes.
|
|
UNIMAT%u2122 Sol Ultra 4FA62 is a panel of PSE-Graphite%u2122 Neopor® on board rabbets.
It is particularly intended for the insulation of the heating grounds (electric, with water circulation and reversible).
|
|
|
The pressed Dämmplatte from Steinwolle with special fiber adjustment and intensified connection is moved for middle loads under swimming being subject grounds.
|
|
|
A special fiber adjustment with intensified connection makes the Dämmplatte 341 particularly resistant.
|
|
|
|
|
|
EUROSOL Thermo isolation of the floors
SCOPE OF APPLICATION: System of heat insulation used, in new work and rehabilitations, for all the types of existing floors on the market, including for all the systems of heating (hot water - electric floor radiating) and of cooling by the ground.
FEATURES: The EUROSOL is a panel of heat insulation out of rigid polyurethane foam (PURE) manufactured without CFC nor HCF, faced of a watertight facing composite polyethylene, aluminum and kraft on the two faces. A face receives a black squaring with the step of 10 cm.
Dimensions of the panels:
Matched grooved edges: 1000 X 1200 mm useful 990 X 1190 mm
Thicknesses: 30,41,51,56,63,80 Misters.
Density of foam: density 30 kg/m3 ± 2.
Classify compressibility: European classification SC1 has 2 Ch
Thermal coefficient of conductivity certified: 0,024 W/m.K
ACERMI N° 03/003/281 Classification INSULATES: I5 S1 O2 L2 E1
The floors isolated with EUROSOL can receive a stuck floor covering (on cover concrete), seal or a floating hardwood floor.
|
|
JACKODUR® KF Standard is a high-quality thermal insulation in extruded polystyrene foam (XPS). It is particularly suitable for basement / perimeter applications as it is compression proof, dimensionally stable, moisture and rot resistant. It can therefore also be used in standing water and as load-bearing foundation slabs.
JACKODUR® KF Standard thermal insulation for basement/perimeter is available in a number of different variations:
* compressive strengths 300 kPa / 500 kPa / 700 kPa
* smooth, extrusion-compressed surface
* edge profiles: shiplap (SF), butt edge (GL) or tongue and groove (NF)
* thickness between 30 and 320 mm depending on the format desired
* surface area covered depends on format, e.g. 1250x600 mm = 0.75 m² or 2500 x 600 mm = 1.5 m²
|
|
High performance rigid extruded polystyrene insulation - thermal conductivity 0.029-0.036 W/mK
High compressive strength - available in a number of grades to suit application
No requirement for a separate vapour control layer
When used beneath floor slab, provides a smooth stable platform for the DPM
CFC/HCFC-free with zero Ozone Depletion Potential (ODP)
|
|
Premium performance rigid phenolic insulation -
thermal conductivity 0.021-0.024 W/mK.
Negligible smoke obscuration.
Class O / low risk fire rating.
No requirement for a vapour control layer.
Quick response floor heating - prevents heat loss through "heat sump".
Minimises the cost of related items %u2013 soil removal, DPMs, service connections.
|
|
High performance rigid urethane insulation - thermal conductivity 0.022 - 0.023 W/mK
No requirement for a vapour control layer
Quick response floor heating - prevents heat loss through "heat sump"
Minimises the cost of related items - soil removal, DPM's, service connections
|
|
High performance rigid extruded polystyrene insulation - thermal conductivity 0.029 W/mK bonded to T & G chipboard
No requirement for a vapour control layer
Eliminates the need for wet screeds
Excellent compressive strength
|
|
|
|
|
|
The JACKODUR Atlas perimeter insulation system combines all the qualities expected of modern thermal insulation for use in passive-house design:
* Free from thermal bridges – Unlike standard construction work, where thermal bridges are usually suitable, thermal bridges are not acceptable in passive-house constructions. A thermal bridge is considered to be insignificant when Ψ ≤ 0.01 W/(m-K). JACKODUR Atlas is fully compliant with this requirement.
* Cost effectiveness – It combines thermal insulation with a formwork system, so that both are achieved in a single step. Stripping the formwork is not necessary. And this, together with the single-layer application, means significant time – and therefore cost – savings.
* Structural physics under control – Thanks to its unique connection system (patent pending), laying mistakes, and therefore thermal bridges, are eliminated, and a structurally correct single-layer application is guaranteed.
* Durable and secure – The tried-and-tested JACKODUR base material ensures that your building is durably insulated with secure foundations.
* Depending on the format desired, JACKODUR Atlas is available in 300, 500 or 700 kPa
JACKODUR Atlas is available as a complete system:
* made to measure according to your architect’s specifications
* essentially all geometries can be produced
* complete system delivered directly to the building site
* precisely tailored construction simply by following the detailed laying instructions supplied
* eliminates the need to adjust or cut to size
Alternatively, the elements can be assembled individually.
|
|
Expanded polystyrene panel of strong density on right board. This PSE is of color silver plated gray.
Panel in PSE of strong density on right, gray board silver plated. EPSISOL gets busy for the insulation of the grounds of the apartment buildings, tertiary sectors and of the establishments receiving of the public. It is intended for the thermo isolation:
- under-face of the quay levels of houses,
- under cover of the floors located in top of basement, on underfloor space, external passage or quay level,
- floors (low or intermediaries) heating with warm water low temperature, reversible and radiant electric.
|
|
|
|
|
|
Springvale Floorshield has been providing the effective, efficient and cost-effective solution to insulating a wide variety of solid and suspended floor constructions for decades, making substantial contributions to energy efficiency.
An expanded polystyrene rigid insulation board, it is available in original white EPS or as Platinum, to provide even higher insulation values.
Platinum Floorshield is an EPS board which incorporates a graphite component called Neopor®, manufactured by BASF, to provide significantly improved thermal insulation performance, for example, to achieve higher levels of the Code for Sustainable Homes or just to improve SAP ratings.
Floorshield products are light and easy-to-handle and can be fitted simply in domestic, commercial and industrial ground floor applications. Floorshield is suitable for use in solid concrete floors above or below the ground bearing slab; above a suspended beam and block floor; within a suspended timber floor and below under floor heating systems.
The inherent insulation and compressive strength properties of this versatile material make it the most cost-effective loadbearing insulant for floor construction, with a compressive strength at 1% compression of 21 kPa. Springvale Floorshield products are the ideal solution for domestic applications.
Providing excellent thermal insulation properties, Floorshield and Platinum Floorshield reduce heat loss, conserve energy and can be used in conjunction with other products in Springvale%u2019s Shield range to assist compliance with the Code for Sustainable Homes.
|
|
UNIMAT%u2122 Sol Ultra 4FA62 is a panel of PSE-Graphite%u2122 Neopor® on board rabbets.
It is particularly intended for the insulation of the heating grounds (electric, with water circulation and reversible).
|
|
JACKODUR® KF Standard is a high-quality thermal insulation in extruded polystyrene foam (XPS). It is particularly suitable for basement / perimeter applications as it is compression proof, dimensionally stable, moisture and rot resistant. It can therefore also be used in standing water and as load-bearing foundation slabs.
JACKODUR® KF Standard thermal insulation for basement/perimeter is available in a number of different variations:
* compressive strengths 300 kPa / 500 kPa / 700 kPa
* smooth, extrusion-compressed surface
* edge profiles: shiplap (SF), butt edge (GL) or tongue and groove (NF)
* thickness between 30 and 320 mm depending on the format desired
* surface area covered depends on format, e.g. 1250x600 mm = 0.75 m² or 2500 x 600 mm = 1.5 m²
|
|
High performance rigid extruded polystyrene insulation - thermal conductivity 0.029-0.036 W/mK
High compressive strength - available in a number of grades to suit application
No requirement for a separate vapour control layer
When used beneath floor slab, provides a smooth stable platform for the DPM
CFC/HCFC-free with zero Ozone Depletion Potential (ODP)
|
|
|
|
|
|
The JACKODUR Atlas perimeter insulation system combines all the qualities expected of modern thermal insulation for use in passive-house design:
* Free from thermal bridges – Unlike standard construction work, where thermal bridges are usually suitable, thermal bridges are not acceptable in passive-house constructions. A thermal bridge is considered to be insignificant when Ψ ≤ 0.01 W/(m-K). JACKODUR Atlas is fully compliant with this requirement.
* Cost effectiveness – It combines thermal insulation with a formwork system, so that both are achieved in a single step. Stripping the formwork is not necessary. And this, together with the single-layer application, means significant time – and therefore cost – savings.
* Structural physics under control – Thanks to its unique connection system (patent pending), laying mistakes, and therefore thermal bridges, are eliminated, and a structurally correct single-layer application is guaranteed.
* Durable and secure – The tried-and-tested JACKODUR base material ensures that your building is durably insulated with secure foundations.
* Depending on the format desired, JACKODUR Atlas is available in 300, 500 or 700 kPa
JACKODUR Atlas is available as a complete system:
* made to measure according to your architect’s specifications
* essentially all geometries can be produced
* complete system delivered directly to the building site
* precisely tailored construction simply by following the detailed laying instructions supplied
* eliminates the need to adjust or cut to size
Alternatively, the elements can be assembled individually.
|
|
|
Glulam is a high-quality material which is useful in a wide range of applications and possesses outstanding properties. It can be incorporated ideally in interior design and is particularly attractive.
|
|
|
The advantages of NORDLAM »ExpressElements« ceiling components are obvious. Simple and quick assembly is possible using the Rampa fittings which are included with the sections. The ceiling can be walked on as soon as it has been installed. The stability is therefore not compromised and the appearance of the underside is excellent. Depending on the application, the underneath can be left as a visible ceiling. From an environmental point of view, wooden ceiling constructions create a very pleasant climate in the room. Installations, even refits, are no problem.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
Glulam is a high-quality material which is useful in a wide range of applications and possesses outstanding properties. It can be incorporated ideally in interior design and is particularly attractive.
|
|
|
The advantages of NORDLAM »ExpressElements« ceiling components are obvious. Simple and quick assembly is possible using the Rampa fittings which are included with the sections. The ceiling can be walked on as soon as it has been installed. The stability is therefore not compromised and the appearance of the underside is excellent. Depending on the application, the underneath can be left as a visible ceiling. From an environmental point of view, wooden ceiling constructions create a very pleasant climate in the room. Installations, even refits, are no problem.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
The pressed Dämmplatte from Steinwolle with special fiber adjustment and intensified connection is moved for middle loads under swimming being subject grounds.
|
|
|
A special fiber adjustment with intensified connection makes the Dämmplatte 341 particularly resistant.
|
|
|
|
see the results for the following category : 
