|
|
Weight: appr. 6,0 kg/m² (1,23 lbs/sqft)
Open area: appr. 51%
Main applications: Facade, Ceiling, Space
the flat surface on one side of the EGLA-TWIN creates a reflection across the full plane
In the direction of the thinner twin wires the mesh is relatively flexible and can be easily adjusted to certain radii |
|
HunterDouglas® Aerofoils are standard available in 6 different sizes and in an adjustable or fixed configuration. The specific fin design allows for larger spans and there is a choice of support structures.
FIXED FIN ANGLE
• The fixed fin support structure has been designed to accommodate any
angle between 0° and 180° with increments of 5 degrees. The fin angle
can be set during installation.
• Fixed fin V-bracket, available in 0, 30 and 45 degree for the 200 - 300AF.
• Fixed fin Cup-bracket, available in 0, 30 and 45 degree for the 350 -
450AF.
The adjustable Aerofoil system gives the user the option of setting the fins at any possible angle from 0 to a maximum of 120 degree at any time. With this motorised system, maximum convenience can be obtained with the optional intelligent control system, which automatically regulates the fins according to the sun path. The high quality materials guarantee this system to operate with a minimum of maintenance. |
|
The Luxalon® 70S and 132S Sun Louvre system consist of sturdy Z-shaped panels. The panels are used to achieve a crisp Sun Louvre or façade and result in an aesthetically pleasing overall appearance.
• Roll formed aluminium panels of 70 or 132 mm wide
• Coil coated with UV and scratch resistant Luxacote® coating available in 14 standard
colours. Other colours on request.
• Stylish carrier rails with sliding brackets allow a variable module by which openness
and shading angle can be selected
• 70S and 132S panels can be combined on one support rail
• The Luxalon 70S and 132S system can be installed in three ways:
- Projected horizontally at the top of the glazed area or roof edge
- Positioned vertically
- Combination of horizontal and vertical
- Corner solutions available
• The vertical Luxalon® 70S and 132S sun louvres combine multiple
functions in a single product:
- The Z-shaped panels have been specially developed as a Sun Louvre
system for façades exposed to low sun angles
- It can also be used as ventilated façade system. Covering for example
installations on rooftops or staircases |
|
DESCRIPTION
Among the building covering solutions available, the Atena Sunscreen staves are especially suited where local screening of direct light is required. Different effects can be obtained as desired, depending on the inclination of the crosspiece used.
TECHNICAL SPECIFICATIONS
External covering with ATENA SUNSCREEN type staves, obtained form profiling of aluminium strips pre-painted on one or both sides, thickness 6/10. Inclination of the staves at45°, 30° or 20° is provided by the various selection of support crosspiece realised by profiling of special aluminium alloy strips with a thickness of 10/10, painted white on both sides. |
|
| Continuous louvre system blade (pitch 150mm): sheet aluminium blade, perforated underside, packed with inorganic mineral wool for acoustic performance |
|
| In order to control the thermal gain and the natural day light entry, Renson has developped the SUNCLIPS® Patio: sunshading aluminium sliding panels |
|
Horizontal aluminium solar shading system with C-shaped blades clipping on a support structure
|
|
Aluminium solar shading with aerofoil blades in fixed position
|
|
Vertical aluminium solar shading system with C-shaped blades clipping on a support structure
|
|
Aluminium solar shading with aerofoil blades is a DIY-kit ready to be installed
|
|
Lockline aluminuim screens enhance privacy as well as security in a myriad of applications both inside and outside the home. The modern stylish look of Lockline lends itself to today's designs and a wide range of finishes are available. Mill finish lends itself to the industrial look however where a softer look is required anodising and powder coating are both available. Powder coating is available in an extensive range of colours for both internal and external applications. With a range of options of aperture sizes and panel depths Lockline has proven its versatility in a wide variety of projects. Designed to reduce the effects of direct sunlight on a building façade Lockline sunscreens reduce energy consumption while at the same time providing a near uninterrupted view of the surroundings. Approximately one third the weight of an equivalent steel profile, Lockline aluminium sunscreens offer construction savings as they can be installed easily without the need for bulky support structures.
Lockline sunscreens can be installed vertically, horizontally or at any angle in between. When installed horizontally it is possible for the sunscreen to provide a dual role as both sunscreen and as a walkway for maintenance access or for window cleaning. Vertical screens on the other hand can be used to hide unsightly areas around the building including bin storage areas, plant and equipment locations and vehicle access ways. Lockline screens can be manufactured in individual panel sizes up to a maximum of 6m x 1.2m. Larger areas can be achieved by joining edge bars or extending the swage bars.
|
|
Webforge privacy screens are manufactured in Europe from aluminium. Manufactured by the press locked method they can be provided in either anodised or powder coated finish in a wide range of colours. Available with aperture sizes varying from 20mm square (22mm x 22mm) up to 50mm square(55mm x 55mm) in 10mm increments. Using slim line aluminium load and cross bars these screen panels are suitable for a wide range of applications both internal and external.
Used extensively throughout Europe, externally these screens provide the perfect solution for disguising common eyesores such as bin storage areas, pool equipment and air conditioning platforms and other service areas.
Internally they are ideal for suspended ceilings and room dividers or as a protective screen to an open flight of stairs.
Privacy Louvres
This newly developed full press locked louvre panel combines excellent technical qualities with elegant design and thus offers a variety of new solutions within the current louvre market.
With this new louvre panel engineers and architects can design sun control systems, façade elements or gangways without destroying the architectural concept of the building. When used in gangways or walkways these louvres provide a high level of privacy with the angle of the louvre blade reducing visibility from below the walkway. With a variety of blade angles available this new product is the product of choice in a wide variety of applications.
Cross bar (louvre) lengths are limited to 1200 mm.
|
|
Direct sunlight causes glare and unwanted heat on window areas. Outlook Sunscreens are carefully designed and installed to deflect and eliminate this problem, without shutting off the outside view. Manufactured from durable aluminium, Outlook Sunscreens allow free movement of air around building exteriors and yet add a distinctive design element that can enhance a buildings appearance.
Webforge offers a comprehensive service for the design and manufacture of sunscreens, specifically for your project and budget.
Outlook Finishes
Outlook Sunscreens are available in a wide range of colours and can be anodised or powder coated. Special requirements in colour or finish can be catered for. Outlook Sunscreens can also be used in a natural mill finish.
Approved Testing
Extensive wind tunnel and impact testing by C.S.I.R.O., Monash University and the James Cook University has shown Outlook Sunscreens will meet the tough standards required for cyclonic and debris protection. The proven strength of Outlook also makes it an ideal security medium.
|
|
Outdoor wooden blinds
The exclusive discovery of facades dressed
with wooden slats which can be lift up and adjusted.
Softened sunlight for outdoor application
For your glass roofs and verandas. |
|
| Faber venetian blinds with aluminium slats were introduced for the first time in 1949, and not many homes in Denmark have been without venetian blinds since, typically those in classic white. |
|
Solar protection
Sun-break hung without altering the weather-proofing of the façade, by using inside frame gaskets.
Easily adapted to solar protection, using punctual pressure.
Choice of protection :
• "SCREEN" sun-blind
• Adjustable vertical louvers
• Fixed louver sun-break
• Combination aluminium louvers and "SCREEN" sun-blind
• guaranteed comfort and light control, whatever the position of the sun.
|
|
LINEA G
Blades: 44 cm in width. Manufactured from aluminium sheet from 8/10 up to 10/10 thick, pre-painted PVF or anodized, internally strengthened with structural ribs; the heads are of pressed aluminium or reinforced nylon. Max height 5,00 m.
Frames: natural extruded anodized aluminium, with more sections dependent on dimension of the blade and according to aesthetic needs; external connecting-bar in natural extruded anodized aluminium on bronze washers and inox nuts.
Controls: teleflex manual control type, with reducer or electrical linear action.
Colours: standard colours are white ral 9010 and silver ral 9006. We can supply all ral colours, upon request. |
|
Type S
Blades 22-27-34-40-47-60 cm width, elliptical profile manufactured from pre- painted aluminium sheet 0,8-1,0-1,2 mm thick, reinforced inside by extruded aluminium "I" section. Shaped end blocks fit inside the louvre skin, manufactured from nylon or die-cast aluminium. The end blocks retain the "I" reinforcing position. Extremely high deflection resistance.
Maximum height of one louvre 3 metres for blades 22 cm, 4 metres for blades 34 and 40 cm, 6 metres for 47 cm, 8 metres for 60 cm.
Frames: natural extruded anodized aluminium, with more sections depending on the dimension of the blade and according to aesthetic needs. External connecting-bar in natural extruded anodized aluminium on bronze washers and inox nuts.
Controls: teleflex type manual control, with reducer or electrical linear action.
Colours: standard colours are white ral 9010 and silver ral 9006. We can supply all ral colours upon request |
|
TYPE HT
Blades: High Tech available in two models of 205 and 530 mm wide, manufactured with perforated calendared aluminium sheet (pitch, section and disposition of the holes are supplied upon request), with lateral bending to give rigidity, fixed to a light structure composed of a central tube in extruded aluminium and some brackets fixed to the supporting tube with non visible screws.
Supports, sea-gull-shaped in the 530 model and triangular shaped for the 205 model, are manufactured in aluminium and shaped to give physical and aesthetic lightness to the blade. At one of the extremities of the blade there are some connecting rods for the fixing of the movement system.
The dimensions of a complete blade 530 are: 530 mm wide and 97 mm thick for a variable length up to 5 mt; the 205 blades are: 205 mm wide, 55 mm thick and of a variable length up to 2,5 mt.
Frames: natural extruded anodised aluminium, with more sections depending on the dimension of the blade and according to aesthetic needs. External connecting-bar in natural extruded anodised aluminium on bronze washers and inox nuts
Controls: reducer or electrical linear action 220 V. |
|
TYPE F
Sun protection composed of an aluminium profile. The system provides two types of blades:
- F1 is Z shaped;
- F2 is round.
Both F1 and F2 are 142 mm wide and are finished in either pre-painted aluminium on the external face (on both sides if requested) and in various colours. This system can be assembled very quickly and is extremely versatile. Versatility enables to chose the distance between blade centers (minimum distance 160 mm).
Additional blades must be supported every 1,5 to 1,8 m. Colours: standard colours are white ral 9010 and silver ral 9006. We can supply all Ral colours upon request |
|
Type E 75
Type E 75 screens are non retractable but only adjustable, designed to be installed onto horizontal, vertical, sloping or unusually shaped windows.
Blades:of round shape are 75 mm wide, in extruded anodised aluminium, 25/10 thick, held by movable nylon supports, with an overlap between the blades of 5 mm (distance 70 mm)
Frames:in extruded anodised aluminium with nylon supports on which the blades are fixed.
Blades rotate with an extruded anodised aluminium bar.
Distance between the frames 1,3 m.
Control: handle manual control with reduction or rotating tubular motor with single phase 220 V.
Colors: standard natural anodized. On request all RAL colours. |
|
Type S wood
Blades: 15 cm in width. In solid wood (red cedar, oak, iroko and teak) water paint soaked, closed by pressed aluminium heads, internally strengthened with structural ribs; Max height 2 m.
Frames: natural extruded anodized aluminium, with more sections depending on the dimension of the blade and according to aesthetic needs; external connecting-bar in natural extruded anodized aluminium on bronze washers and inox nuts.
Controls: teleflex type manual control, with reducer or electrical linear action. |
|
|
|
