|
|
A simple and effective adjustable cable in stainless and carbon steel.
Rated B.L.:
GS - Up to 1189kN / 121240kg / 267290lb
SS - Up to 945kN / 96420kg / 212330lb
Cable Diameters: 3mm to 36mm
Specific Features:
- Simple easy tensioning by adjusting the locknuts.
- Adjustable at both ends.
- Threaded ends can be secured to suitably threaded anchorages.
- Used where cable termination points are directly aligned.
- Nuts and washers require suitable bearing surfaces or plates.
|
|
The Guy Linking Cable System consists of a range of stainless steel architectural cable assemblies, ideal for many structural and architectural applications.
All Guy Linking tendons use high-grade 316 stainless, which ensures a long service life with very little maintenance.
Guy Linking Cable Tendons (using swaged and threaded components).
Macalloy currently have the capacity to swage stainless cable assemblies ranging from 3mm to 26mm. There are three types of standard strand construction available;
* 1x19 Spiral Strand, the wires have a smooth bright finish with moderate initial stretch properties.
* Compact Strand, offers 30% increase in breaking load over conventional 1x19 strand
with a much lower initial stretch.
* 7x19 Strand, ideal for situations where flexibility is a requirement.
|
|
|
|
|
|
After the success of the Macalloy 460 and S460 systems, and also in order to meet the ever increasing needs of its customers, the Macalloy SC460 Stainless Cable System has been introduced.
This specially designed system incorporates cable adaptors, which allow standard Macalloy S460 range of forks. By using the standard Macalloy S460 forks on the cable ends, continuity of design remains in projects where standard Macalloy 460 & S460 bar systems have been used alongside the Macalloy SC460 stainless Cable Systems.
The cable used in the system undergoes both a conventional elastic stretch as well as an initial stretch can be between 0.10 and 0.75% of the cable length, depending on the magnitude and frequency of loading, and should always be considered in the design of the structure.
Macalloy offers three types of cable:
* 1x19 spiral strand, has moderate initial stretch properties. All the cable adaptor fittings are designed to match the minimum breaking load of the 1x19 cable.
* Compact Strand, has a higher breaking load along with a lower initial stretch than the 1x19 strand cable and is available in most diameters.
* 7x19 strand is the most flexible cable is available in most diameters.
|
|
|
Turnbuckle jaw-press small terminal suitable for tensional structure and banisters made of stainless steel Aisi 304 and Aisi 316
|
|
The new Macalloy compression struts are available in stainless and carbon steel in diameters M12 to M100 and provide an architectural solution for structural members that are required to act in compression.
A typical Macalloy compression strut utilises standard Macalloy 460 and 520 fork end fittings and pin sets. These connect to specially designed cones that in turn are welded onto each end of a CHS (circular hollow sections).
The use of the Macalloy systems as a compression strut is also approved in Germany by the Deutches Instit für Bautechnik under approval number Z-14.4-530.For further information please contact the Macalloy technical department.
|
|
|
Press jaw terminal made of stainless steel Aisi 304 and Aisi 316 with accurate design.
|
|
|
|
|
|
An attractive jaw (clevis) type cable system in stainless and carbon steel offering increased level adjustment.
Rated B.L.:
GS - Up to 1189kN / 121240kg / 267290lb
SS - Up to 945kN / 96420kg / 212330lb
Cable Diameters:
Type 1: 3mm to 10mm stainless steel.
Type 2: 12mm to 26mm stainless steel.
Type 3: 28.6mm to 36.3mm stainless steel.8.1mm to 36.3mm galfan coated carbon steel.
Specific Features:
- Fully adjustable cables offering increased adjustment with the inclusion of a turnbuckle one end.
- Type 1 and Type 2 cables have turnbuckles with moving parts of dissimilar metals to avoid thread seizure under load.
- Type 1 and 2 cable end fittings have articulating (toggle) jaw ends offering adjustment in two planes to accommodate some cleat misalignment, and relieve stresses caused by dynamic and cyclical loads.
- Type 3 cables have turnbuckles designed specifically for large diameter applications and are manufactured to nominated design loads.
- All ends offer simple and easy connection with clevis and split pins.
- All turnbuckles offer lock nuts to positively lock adjustment.
- A robust structural cable offering maximum adjustment.
- Can accommodate moderate dynamic loads.
- Type 1 and 2 cables can accommodate misalignment of the cleats of +/- 10 degrees.
|
|
The ultimate aesthetic adjustable structural cable tendon.
Rated B.L.:
Up to 285kN / 29060kg / 64070lb
Cable Diameters:
4mm to 22mm
Specific Features
- A minimalist, sleek and compact cable solution for static architectural applications.
- Ultimate aesthetics in stainless steel.
- Fully adjustable telescoping end fittings.
- Fully concealed threads.
- Moderate adjustment.
-A simple and effective adjustable cable.
|
|
|
|
|
|
Macalloy 460 is a fine grain steel with an exceptional blend of mechanical properties; combined with rolled threads this provides a material with superior fatigue performance. Macalloy 460 is a weldable steel with a maximum carbon equivalent of 0.55%.
All fittings are designed and tested to provide a tensile capacity equal or superior to that of the theoretical strength of the bar. The Macalloy 460 system is designed in accordance with the steel work design code BS5950, and is also UK CARES approved for conformance with the design of steel structures: general rules for building DD ENV 1993-1-1:1992 (EC3).
The standard left hand right hand tendon will provide adjustment to accommodate site and manufacturing tolerances:
* Cutting tolerance for bars: up to M76 +/- 6 mm
* Cutting tolerance for bars: over M76 +/- 25mm
* Adjustment for tendons M12 to M56 +/- ½ thread diameter each end
* Adjustment for tendons M64 to M100 +/- 25mm each end
Macalloy 460 can be provided with any practical coating system in accordance with your specification; such as galvanising, sherardizing or painting. Please discuss your exact requirements with the Macalloy engineers.
Architectural fittings are finished to provide a smooth transition from the bar to the fork. This aesthetic appearance is provided by the use of threaded lock covers, which combine the function of a lock nut and a blending thread cover.
The connection to the structure should be made by utilising a web plate with the same thickness and edge distance as the Macalloy spade shown in the product catalogue. All connections should be made using BSEN 10025 Grade S355 material.
|
|
The Macalloy Guy Linking Bar System consists of a range of stainless steel architectural bar assemblies, ideal for many structural and architectural applications. All Guy Linking tendons use high-grade 316 stainless, which ensures a long service life with very little maintenance.
Guy Linking stainless bar tendons combine durability with aesthetics, whilst ensuring that loads are safely and efficiently transmitted. The most common bar applications include:
* Membrane Structures
* Lightweight Steel Structures
* Footbridges
* Glass Facades
* Balustrade
* Guy Linking Bar Tendons (using threaded components)
The Guy Linking stainless bar tendons are available in diameters ranging from 6mm to 35mm diameter.
All Guy Linking bar components are made from austenitic stainless steel Grade 316 to BS970.
All threaded components are designed to match the bar capacity, and are available in a variety of finishes.
|
|
|
|
|
|
The high tensile stainless rod with optimal aesthetics, efficiency and performance.
Lengths/Span:
Up to 3.6m (12’) before joiners are required.
Rod Diameters:
Up to 25.4mm (1”) as standard, or up to 31.8mm (1.25”) upon request.
Specific Features:
- Minimalist design ensures compact neat details.
- Easy adjustment of the rod from one end enables simple access and fast installation reducing time on site.
- No exposed threads ensuring the 'sleekness' of the rod is carried through the entire system.
- Highest load capacity of Ronstan's Structural Stainless Steel Rods.
- Clean polished stainless steel finish to withstand the harshest environments.
- High strength to weight ratio allows the mass of your structure to be kept low while minimising material and transport costs.
- High corrosion resistance and low maintenance due to material choice decreases the life cycle cost of the structure.
- Range of surface finishes - #7 Polished and passivated (standard option), #4 Satin. Others by request.
|
|
An attractive carbon steel rod system of unparalleled tensile strength
Rod Diameters:
M10 (0.394”) to M100 (3.940”)
Lengths/Span:
6.0m (19.6’) for diameters M10 (0.394”) to M16 (0.630”)
9.0m (29.5’) for M20 (0.787”), and 11.95m (39.2’) up to M100 (3.940”) before joiners are required
Specific Features:
- Highest load capacity of Ronstan’s Structural Carbon Steel Rods reducing the mass of your structure with flow on benefits in transport and construction costs.
- Large range of sizes to suit all applications allowing consistency in detailing throughout a project.
- Range of surface finishes - Galvanised to BS EN ISO 1461-1999 or raw finish allows for on-site painting matching ARS4 to your structure in colour and finish.
- Attractive tapered nut and recognisable “tear drop” fork for a simple detail that will not date.
- Simple connection detail of pin and fork minimising installation time and difficulty.
- A fine grain carbon steel.
|
|
The all purpose carbon steel rod system
Lengths/Span:
6.0m (19.6’) for diameters M10 (0.394”) to M16 (0.630”)
9.0m (29.5’) for M20 (0.787”) to M90 (3.425")
11.95m (39.2’) up to M100 (3.940”) before joiners are required
Rod Diameters:
M10 (0.394”) to M100 (3.940”)
Specific Features:
- Large range of sizes to suit all applications allowing consistency in detailing throughout a project.
- Range of surface finishes - Galvanised to BS EN ISO 1461-1999 or raw finish allows for on-site painting matching ARS5 to your structure in colour and finish.
- Attractive tapered nut and recognisable "tear drop" fork for a simple detail that will not date.
- Simple connection detail of pin and fork minimising installation time and difficulty.
- A minimum yield stress of 460 N/mm² ensures that the system is approximately 30% stronger than standard grade S355 or lesser carbon steels.
|
|
A simple and effective stainless rod for moderate loads
Rod Diameters:
Up to 31.8mm (1.25”)
Lengths/Span:
3.6m (12.0’) in diameters 4.8mm (0.188”)- 12.7mm (0.500”)
6.0m (19.6’) for 19.05mm (0.626”) - 31.8mm (1.250”) before joiners are required
Specific Features:
- An economical solution when the high level finish of stainless steel is required, providing affordable good looks.
- ARS3 - the perfect marriage of economy, strength and corrosive resistance.
- The proven design provides ageless integrity to your structure.
- 316 grade stainless steel.
- Range of surface finishes - #7 Polished and passivated (standard option), #4 Satin, electropolished. Others by request.
|
|
|
Range wide of accessories inox for implantation and tensionamento metallic cables for different employs, accessories to mechanical implantation.
|
|
The name of Glover has been associated with the Wire Rope- making industry since Wire Ropes were first used over a century ago, and we are in a position to supply all types of ropes in use, from the very small cords up to the larger sizes of Crane and Lift Ropes.
The Engineering and Construction industries use Wire Ropes in the following broad classifications:
Round Strand Ropes cover the majority of applications.
These ropes have 6 round strands over a central core of Fibre or Steel. Also available in Compacted form to give higher breaking loads.
Multi-Strand Ropes comprises ropes with more than one layer of strands, the directions of lay of each layer being arranged to achieve a balanced and relatively rotation resistant rope.
|
|
|
|
|
|
- Hot Dip galvanized.
- End fittings are Quenched and Tempered, bodies heat treated by normalizing.
- Hooks are forged with a greater cross sectional area that results in stronger hook with better fatigue properties.
- Modified UNJ thread for improved fatigue properties.
- Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckle sizes 1/4" through 2 1/2", a shackle one size smaller can be reeved through eye.
- Forged jaw ends are fitted with bolts and nuts on sizes 1/4" through 5/8", and pins and cotters on sizes 3/4" through 2 3/4".
- TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
- Lock Nuts available for all sizes.
- Crosby's Quenched and Tempered end fittings and normalized bodies have enhanced impact properties for greater toughness at all temperatures.
- Typical hardness levels, Tensile Strengths and Ductility Properties are available for all sizes.
- Turnbuckles can be furnished proof tested or magnaflux inspected with certificates if requested at time of order.
- Turnbuckle assembly combinations include: Eye and Eye, Hook and Hook, Hook and Eye, Jaw and Jaw, Jaw and Eye.
|
|
Swage sockets incorporate a reduced machined area of the shank which is equivalent to the proper after Swage dimension. Before swaging, this provides for an obvious visual difference in the shank diameter. After swaging, a uniform shank diameter is created allowing for a QUICK-CHECK™ and permanent visual inspection opportunity.
Designed to quickly determine whether the socket has been through the swaging operation and assist in field inspections, it does not eliminate the need to perform standard production inspections which include gauging for the proper after swage dimensions or proof loading.
|
|
|
|
