|
|
The one, management board ActivaSun conceived and made in France
leading-edge technology in the management of solar light allows
to control several parameters:
- Adjustment of the power of lighting on 3 levels/Adjustments of the level of the battery on 3 levels
- Management of the power of lighting according to the consumption of the beach of tension.
- Battery preserved (impossibility of unloading) for one optimized lifespan 5 with 7ans.
- Adjustments of the threshold of lighting and exctinction (in connection with the production of the solar panel)
- Programmable Schedule with lighting.
|
|
|
Fruit of a step of éco-design, floor lamp AUTONOMA is dedicated to the lighting of isolated site. Equip with LED of power which combines luminous performance and energy saving, it is also programmable and intelligent thanks to its presence detector.
|
|
|
|
|
|
TECHNICAL CHARACTERISTICS
FREELUM is a modular unit composed of four parts to fit together.
Total height : 4m.50 to 5m., (with the solar panel), wholly in aluminium, thermo-lacquered (polyester powder)
1°) THE SOLAR PANEL :
- Dimension : 1200 x 520 mm
- Power of charge : 80 to 85 Watts/p
- Fixing by an articulated infrastructure swivelling on 360° allowing the South orientation of the solar panel as well as its, optimal incline angle (45 to 60°).
- Monocrystalline type, life approximately 20 years.
2°) THE LED SOLAR LAMP (IP66) :
- 366 led of 27 candelas, daylight type.
- Life approximately 80.000 hours.
- Patented optoelectronic system EVERLUM allowing the best distribution of the led light on the ground, excluding any luminous pollution.
- Tight infrastructure, shock-proof.
3°) THE MIDDLE TUBE
4°) THE BASE IS COMPOSED OF :
a) TIGHT MOBILE SLIDING TRAP
- Located on the low base plate of the unit, this patented sliding system (ROLLTRAP) protects electronic control and regulation of energy.
b) ELECTRONIC CONTROL AND REGULATION OF :
- The charge of the batteries from the photovoltaic module.
- The current limiting of the leds
- The power of lighting according to the charge of the batteries.
c) THE BATTERIES CONTAINER
- Dimension : 500 mm of height, diameter 300mm
- Fixing with two sliding rings
- Locking anti vandalism on the base
- Contains 2 solar batteries of 40 Ah each one, life of 5 to 7 years.
d) THE BASE TO FIX ON THE GROUND:
- On a base with six points of fixation, to fix on the concrete base with an electrolysis protection according to instructions of installation.
|
|
|
|
|
|
A revolutionary road lighting fixture uses the best technologies available to increase safety for pedestrians, while reducing environmental impact.
Designed by Giugiaro Architettura and manufactured by Disano illuminazione, OnOff was launched at Remade, Portugal, the exhibition of high-tech products that are built using recycled and recyclable materials.
The project is part of a number of events promoted by Cestec, a Lombardy-based company created to support manufacturers in the production of excellent products, using environmentally friendly recyclable materials.
OnOff is a lighting fixture specially developed to increase safety for pedestrians and to reduce environmental impact starting from the production stage.
The luminaire is made of aluminium, an entirely recyclable material, whose design combines a pole and a lighting fixture into one single object.
As to consumption, the opportunity to exploit solar power is the most interesting aspect. In fact, a photovoltaic panel is fitted on the lamp cover. That means that OnOff can be powered independently without connecting it to the mains. The batteries provide in any event a five-day run time in the absence of solar radiation.
The photovoltaic system turns solar power into electricity, thanks to the use of semiconductor materials such as silicon, which is reduced to sheets to create photovoltaic cells.
|
|
|
New solar lighting Sun-26 (Sox 26) uses photovoltaic cells to convert the solar radiation into emectric energy. This energy is emmagisinée in a battery during the day and is restored the night to supply a lamp with sodium vapor.
|
|
Daylight received by a solar module fixed at the top of the floor lamp is transformed into electricity. This one is stored the day in the batteries, then is used starting from the twilight to ensure a lighting of 8:00 (optimum condition of sunning).
Luminous power of the projector (3600 Lumens) with for vocation the lighting of security of allotments, carparks, industrial park, isolated bus shelters.
Characteristics:
Height of mast of 5 mêtres. Height of fire of 4 mêtres. Lighting: 25 luxes with the foot of the candelabrum, 2 luxes with 10 Mr. Lampe: SOX 26 W, Sodium low pressure
|
|
The Verdant Walk, Cleveland, OH
Project concept and design by North Design Office for Cleveland Public Art
Photography: North Design Office
The green city of the future shines through this sculptural installation for a Cleveland art park. The park reflects two forces: the city’s heritage of craftsmanship and its new green agenda. We covered irregular forms with flexible, solar-paneled skins; these charge LEDs that glow within the forms at night. The designer asked that our frame look “hand bent”, hence the organic kinks. In winter, the fabric is removed to showcase the metal armatures as sculpture.
|
|
|
The new Solar Street Light HELIOS SOX 26 VARIO is a revolutionary system composed of photovoltaic modules which converts the sunlight into electric power. This energy is stored in a battery during the day and made available in night-time to power a sodium vapour lamp, also thanks to the new intelligent charge regulator GENIUS 15 VARIO. This is the ideal answer when there is the need of lighting squares, streets, crossings and no available electric power grid nearby. The new Solar Street Light HELIOS SOX 26 VARIO typically starts lighting after sunset and stops at sunrise automatically.
|
|
Reinforced cast stone with stainless steel
Granite grey
Acid etched and Waterproofed
340 Kg.
Anchored with screws
High pressure sodium vapour, model MXD-74
Carandini 70 W. IP-55
70 W.
1 unit 70 W halogen. White light (4,200 k)
Methacrylate (10 mm)
|
|
Suitable poles: from 3 to 4 meters high poles.
Body: Made of cast aluminium. Microtextured black colour finished.
Diffuser: Flat toughened glass.
Fixing: Vertical fixing with Ø60mm pole or 3/4" GAS tread.
Protection level: IP66 (luminaire). IK10
Electrical class: Class I. Class II available.
Gear tray: E27/E40
Electrical equipment: The lamp has enough space to keep electrical equipment with different powers according to the table below.
Upward flux ratio: 0,0%
|
|
Suitable poles: From 8 to 12 meters high poles.
Body: Injected aluminium. RAL9007 silver grey colour finished.
Optical Block: High-efficency reflector, finished in anodised aluminium.
Diffuser: Thermically toughened lenticular glass.
Fixing: Vertical/horizontal coupling joint Ø60mm 0º to 15º sloping on vertical fixing, 0º in horizontal fixing.
Protection level: IP66 (optical block), IP44 (luminaire).
IK10
Electrical class: Class I. Class II available.
Gear tray: E40
Electrical equipment: The lamp has enough space to keep electrical equipment with different powers according to the table below.
Upward flux ratio: 0,06%
|
|
Suitable poles: From 3 to 6 meters high poles.
Body: Injected aluminium. RAL9007 silver grey colour finished.
Diffuser: Thermically toughened lenticular glass.
Fixing: Top fixing with Ø60mm coupling joint.
Protection level: IP66 (optical block), IP65 (luminaire).
IK10
Electrical class: Class I. Class II available.
Gear tray: E27/E40
Electrical equipment: The lamp has enough space to keep electrical equipment with different powers according to the table below.
Upward flux ratio: 0,0%
|
|
Suitable poles: from 3 to 4 meters high poles.
Dome: Made of aluminium
Diffuser: Policarbonate.
Deflection slats: Black aluminium on the outside and anodized on the inside.
Base: Made of aluminium, grey oxiron finish. Vertical fixing on Ø60mm pole by 3 ALLEN M10 screws.
Protection level: IP44 (luminaire).
IK06
Electrical class: Class I. Class II available.
Gear tray: E27/E40
Electrical equipment: The lamp has enough space to keep electrical equipment with different powers according to the table below.
Upward flux ratio: 5,2%
|
|
Location: Recommended pole for residential and green areas, pedestrian and recreational zones, parks, squares and neighbourhoods.
Description: 3350 / 4500mm high pole designed in two pieces. 1175mm high triangular base with rounded vertex and decorative bended strips. Adaptable joint of 75mm and Ø60mm to fix the luminaire to the pole in vertical position.
Material: Base made of steel S-235-JRC, black oxiron finished.
Anchoring: M18 x 500mm embedded bolts (IA01).
|
|
Location: Recommended pole for residential and green areas, pedestrian and recreational zones, parks, squares and neighbourhoods.
Description: Troncoconical pole designed in one single piece consisting of two parts of different diameters of cylindrical column. Cylindrical pole joined to the column by means of a tight. Adaptable bracket of Ø60mm to fix the luminaire to the pole in horizontal position.
Material: 1.Galvanized Stylum: Base, shaft and brackets made of galvanized steel; black oxiron painted base and grey oxiron painted shaft (ICST60APP).
2.Stylum mixta: Galvanized steel base and black forge oxiron painted. Shaft and brackets made of stainless steel (ICST60MAPP).
Anchoring: M18 x 500mm embedded bolts (IA01).
|
|
Location: Recommended pole for roadways, wide streets and avenues, and industrial zones.
Description: Telescopica pole consting of cylindrical parts of different diameters. It counts on two brackets. The superior part has 3 different anchoring joints to fix 3 possible projectors.
Material: Heat-galvanized steel pole, black forge oxiron painted combined with grey colour.
Anchoring: M22 x 700mm embedded bolts (IA08)
|
|
Suitable poles: From 5 to 8 meters high poles.
Body: Injected aluminium . Microtextured black colour finished.
Diffuser: Thermically thoughened lenticular glass.
Fixing: Vertical, hanging on Camprodon bracket. Fixed by means of screws.
Protection level: IP66 (optical block), IP44 (luminaire).
IK10
Electrical class: Class I. Class II available.
Gear tray: E27/E40
Electrical equipment: The lamp has enough space to keep electrical equipment with different powers according to the table below.
Upward flux ratio: 0,00%
|
|
Suitable poles: From 3 to 6 meters high poles.
Body: Injected aluminium . Microtextured black colour finished.
Diffuser: Thermically thoughened lenticular glass.
Fixing: Top fixing, Ø60mm exit.
Protection level: IP66 (optical block), IP44 (luminaire).
IK10
Electrical class: Class I. Class II available.
Gear tray: E27/E40
Electrical equipment: The lamp has enough space to keep electrical equipment with different powers according to the table below.
Upward flux ratio: 0,00%
|
|
Location: Recommended pole for residential and green areas, pedestrian and recreational zones, parks, squares and neighbourhoods.
Description: Telescopica pole designed in one single piece of 3600mm high. Rectangular base with rounded vertex of 1150mm high. Adaptable joint of 70mm and Ø60mm to fix the luminaire to the pole in vertical position.
Material: Made of zinc plated steel. Black oxiron heat-painted.
Anchoring: M18 x 500mm embedded bolts (IA01).
|
|
|
STANDARD COLUMN Consisting of a base, a closed module, a semi-closed module, six open modules and a lamp holder in GG-20 pearlitic cast iron, with a height of 9550 mm. 12 anchorage bolts in M-24 zinc-coated steel, 1000 mm in length. VENTILATION GRID Upon request, one of the modules can be fitted with a ventilation grid made out of steel plate, protected with a rust-proof coating (dichromated). TRAP DOOR COVER Made out of hot-galvanised steel plate. HAT The lamp holder is crowned with a polyester hat reinforced with fibre glass. DIFFUSOR: Diffusor in 4 mm thick methacrylate, reinforced at the two ends, 600 mm in diameter and 1000 mm in length. NUTS AND BOLTS In A4 stainless steel.
|
|
|
COLUMN: Cylindrical, heights of 10, 12 and 14 m, 220 mm in diameter, in ST-52 grade steel. Fuse box lid with triangular theft-proof lock. BRACKET: It is available with 1,2, 3 or 4 arms, including wall anchorage bracket. Made out of ST-52 grade steel. Height: 3 m. LAMP FITTING: Made by SILL with cast aluminium casing. BANNER SUPPORT: Solid stainless steel bar and parts with rounded ends. NUTS AND BOLTS: In stainless steel. FOUNDATION: Metal plate with anchorage bolts on 1.5 x 1.5 x 1.5 m concrete footing.
|
|
|
In 1992, Philippe Starck worked with JCDecaux to develop a revolutionary type of streetlight: vertical during the day, it pivoted down at nightfall to direct the beam of light onto the street.
|
|
|
With a unique shape evoking the plant kingdom, both the structures and the glass are available in different colours. COROLLA is the ideal unit to distinguish large streets, commercial roads, parks, gardens and other urban environments, with a modern and elegant style. Available also as a wall fitting option, COROLLA offers the greatest of ease during installation and maintenance, with an accessible frame, even without tools, and a hinged opening to the empty lamp.
|
|
BATTERY CUPBOARD:
Made out of 3 mm thick hot-galvanised plate, with a polyurethane lid.
COLUMN:
Made out of a 4 mm thick DIN 2440 hot-galvanised steel tube, 100 mm in diameter.
SOLAR PANEL SUPPORT:
It consists of a 4 mm thick curved hot-galvanised steel tube, 90 mm in diameter, and a 3 mm thick hot-galvanised plate protecting the rear of the panel.
NUTS AND BOLTS:
In A4 stainless steel.
|
|
|
|
