|
|
|
|
|
|
The POWERDECK is a panel of heat insulation with rigid a foam heart of polyisocyanurate covered, on two faces, of a facing aluminum corrugated 50µ.
Dimensions of the panels: 2500 X 1200 mm, 1000 X 1200 Misters Epaisseurs: With flat rims: 30,40,50,60,70,75,80 Misters.
With edges rabbets on 4 with dimensions: 90,100,120 Misters.
Us to consult for flat rims into 90,100 and 120 Misters.
Useful dimensions of the panels rabbets: 2485 X 1185 mm and 985 X 1185 Misters.
Density of foam: 32 kg/m3 ± 2.
Classify compressibility: >150 kPa for a deformation of 10%.
Rigid insulation and resistant of class C.
Tensile strength perpendicular: >80 kPa.
Behavior in fire: Classification Euroclasse B-s2, d0 on vat steel.
Classification Factory Mutual: classify 1 (according to various complexes of roofing).
Thermal coefficient of conductivity certified: value D: 0,024 W/m.K.
ACERMI n° 04/003/329
Implementation: Support of sealing on steel or wood.
In the receiving case of the buildings of the public, a heat shield will be implemented between the support vat steel and the POWERDECK, in accordance with the provisions of the "Guide of use of combustible insulations in ERP" appendix II of the article AM8, Arrêté of October 6th, 2004 and appreciation CSTB bearing n° RS08-174 on the provisions against the fire hazards in the ERP.
This heat shield can be made up of a bed of panels of pearlite on right board of dimension 1200 X 1000 mm, thickness 50 mm with a thermal resistance R = 1 m2 K/W or of any other type of heat shield defines in the AM8.
|
|
|
|
|
|
Support of sealing for roofing concrete, wood or derived from wood
The good answer for the insulation of the roofings terraces.
EUROTHANE AUTOPRO IF is a panel of heat insulation with rigid a foam polyisocyanurate heart (TAUfoam by RECTICEL) covered, on two faces, of a facing composes of a multi-layer coating seals polyester, kraft and aluminum.
Scope of application:
Last nines and rehabilitation.
All zones of wind.
All types of buildings.
Roofings accessible pedestrians, inaccessible, technical, vegetalized.
Minimum Leger, obstruction, do not overload the structure.
Saving of transport, handling and storage.
Until RD = 10 m2. K/W with 2 beds of 120 Misters.
Dimensions panels: 600 X 600 Misters.
Thicknesses: 30-40-50-60-70-80-90-100-110-120 Misters.
Classify compressibility: >150 kPa rigid insulation and resistant of class C.
Tensile strength perpendicular: >150 kPa.
Thermal coefficient of conductivity: 0,024 W/m.K.
Regulation:
ACERMI n°03/003/127
D.T.A. (Technical opinion) n°5/07-1972
DTU 20.12 and 43.4.
Implementation:
The installation of insulation is done into 1 bed poses free or in 2 beds stuck by studs of cold or fixed adhesive mechanically.
The watertight facing will be either in independence with heavy protector, or apparent poses in semi-independence (membrane bituminizes modified semi-adhesive or fixed mechanically and mechanically fixed synthetic membrane)
|
|
|
|
|
|
Support of sealing for roofing concrete, wood or derived from wood.
Effective and powerful insulation for the roofings terraces accessible, inaccessible and technical.
EUROTHANE Br BIO is a panel of heat insulation with a foam heart
rigid polyurethane covered, on two faces, with a composite facing tight with the air, aluminum and kraft.
Scope of application:
Last nines and rehabilitation.
All types of buildings.
Accessible, inaccessible, technical roofings.
Direct support of independent sealing under heavy protector only.
Until RD = 10,30 m2. K/W with 2 beds of 124 Misters.
Very good dimensional stability.
Dimensions panels: 600 X 600 Misters.
Thicknesses: 30-40-50-60-72-82-90-102-110-120-124 Misters.
Classify compressibility: >150 kPa rigid insulation and resistant of class C.
Thermal coefficient of conductivity: 0,024 W/m.K.
Regulation: ACERMI n°04/003/127
DTA (Technical opinion) n°5/02-1665.
Implementation: on roofing concrete in conformity with the DTU 20.12, slope of 0% has 5%. The installation of insulation EUROTHANE Br BIO is done into 1 or 2 beds in free installation without unit limitation of surface of terrace according to DTA (Technical Opinion)
|
|
|
|
|
|
Insulation by the outside of the tilted roofings (method of Sarking) in climate of plain and mountain.
The EUROTOIT is a thermal rigid polyurethane foam insulation panel (PURE) faced of a watertight facing composite polyethylene, aluminum and kraft on the two faces. Rigid insulation and resistant of class C
Thermal coefficient of conductivity certified: 0,024 W/m.K
Density of foam: density 30 kg/m3 ± 2.
Dimensions of the panels matched grooved edges:
2400 X 1200 mm useful: 2380 X 1180 mm
1200 X 1000 mm useful: 1180 X 980 mm
Thicknesses: 60,80,100,120 mm to consult Us for 40,50,70,90,110 mm
The installation is done according to the schedule of conditions of implementation aimed by Alpha Controls.
Mode of installation: The system applies to a continuous support being able to act as ceiling fixed on a frame wood.
Pose in a bed or two beds up to 240 mm thickness is until RD = 10 m ². K/W.
ACERMI N° 04/003/345
Simplicity of implementation, the total cover of the frame allows the removal of the thermal bridges, protects it from thermal variations thanks to fitment reinforced from the panels and to leave a visible frame of the interior by preserving livable space of the roofs.
Effective in winter, in addition to sound high capacity insulation the EUROTOIT contributes to the thermal comfort of summer by its reflective completion thus allowing an airconditioning energy saving during the hot season.
The EUROTOIT can be used in new building or restoration for
apartment buildings, ERP, buildings labor regulation subject to the respect of the regulations in force.
|
|
|
|
|
|
Support of sealing with form of slope integrated on concrete and wood or derived from wood
Lightness with the service of the insulation of the roofings terraces accessible, inaccessible, technical and vegetalized.
EUROTHANE BI3A is a panel of heat insulation with a rigid foam polyurethane heart covered, on two faces, of a facing made up of a grésé bituminized coating has reinforcement veils glass.
Scope of application:
Last nines and rehabilitation.
All types of buildings.
Roofings accessible pedestrians, inaccessible, technical, vegetalized.
Leger and low thickness, true more in restoration.
Great dimensional stability.
Strong mechanical resistance.
EUROTHANE BI3 has is an insulation with form of integrated slope.
Dimensions panels: 600 X 600 mm, 1200 X 600 mm
Thicknesses: 30-40-50-60-70-81-90-100 - slope 1/80 or 1/60.
Classify compressibility: >120 kPa rigid insulation and resistant of class C.
Tensile strength perpendicular: >80 kPa.
Thermal coefficient of conductivity: 0,028 W/m.K.
Regulation: ACERMI n°03/003/121,
DTA (Technical opinion) n°5/07-1951.
Implementation: The installation of insulation EUROTHANE BI3 has is done into 1 or 2 beds. In free installation with coating in independence under heavy protector. By studs of adhesive EAC with coating bituminizes apparent
|
|
|
|
|
|
Support of sealing on concrete and wood or derived from wood
Lightness with the service of the insulation of the roofings terraces accessible, inaccessible, technical and vegetalized.
EUROTHANE BI3 is a panel of heat insulation with a rigid foam polyurethane heart covered, on two faces, of a facing made up of a grésé bituminized coating with reinforcement veils glass.
Scope of application:
Last nines and rehabilitation.
All types of buildings.
Roofings accessible pedestrians, inaccessible, technical, vegetalized.
Leger and low thickness, true more in restoration.
Great dimensional stability.
Strong mechanical resistance.
Dimensions panels: 600 X 600 mm
Thicknesses: 30-40-50-60-70-81-90-100-110-120 mm
Classify compressibility: >120 kPa rigid insulation and resistant of class C.
Tensile strength perpendicular: >80 kPa.
Thermal coefficient of conductivity:
thickness 60 mm value: 0,027 W/m.K.
Regulation: ACERMI n°03/003/121,
DTA (Technical opinion) n°5/07-1950.
Implementation: The installation of insulation EUROTHANE BI3 is done into 1 or 2 beds. In free installation with coating in independence under heavy protector. By studs of adhesive EAC with coating bituminizes apparent stuck to the EAC or semi-indépendant. By studs of cold adhesive with coating in total adhesion cold.
|
|
|
|
|
|
Insulation of the accessible pedestrians, inaccessible, technical and vegetalized roofings terraces.
Direct support of sealing asphalts.
The EUROTHANE S Plus 25 has is a panel of heat insulation with a rigid foam polyurethane heart covered, on two faces, of a facing made up of a coating veils microphone-perforated glass.
Scope of application:
Last nines and rehabilitation.
All types of buildings.
On roofing concrete, wood or derived from wood.
Implementation easy and fast.
Climate of plain and mountain
Dimensions panels: 600 X 600 Misters.
Thicknesses: 30-40-50-60-70-80-90-100-120 Misters.
Density of foam: 32kg/m3
Classify compressibility: > 150 kPa rigid insulation and resistant of class C.
Tensile strength perpendicular: >80 kPa.
Thermal coefficient of conductivity: thickness from 30 to 60 mm: 0,028 W/m.K, thickness from 70 to 120 mm: 0,027 W/m.K.
Regulation: ACERMI n°04/003/311, DTA (Technical opinion) n°5/04-1770 and DTU 20.12 and DTU 43.4.
Implementation: Free installation, without unit limitation of surface of terrace, on carrying element in:
Masonry slope null, punt and tilted.
Wood and drifts slope of 3 have 5%.
Gas concrete slope punt of 1 has 5% and inclined > 5% have 20%.
|
|
Premium performance rigid phenolic insulation -
thermal conductivity 0.021-0.024 W/mK.
On average its use creates 15% more usable warm roof space.
Negligible smoke obscuration.
Class O / low risk fire rating.
Insulation of pipes and tanks is unnecessary.
No condensation risk.
|
|
High performance rigid urethane insulation - thermal conductivity 0.022 - 0.023 W/mK
Conforms to Robust Details standards
On average its use creates 15% more usable warm roof space
Insulation of pipes and tanks is unnecessary
No condensation risk
|
|
ISOTEC® is an insulating and structural panel, the below- tile-panel for new roofs and redoing old roofs.
ISOTEC® consists of an insulating core made of rigid polyurethane foam covered in water and flameproof embossed aluminium complete with a steel tile-bearing section.
Holes built into the section channel any leaks by the top roofing layer right into the eaves.
The holes ensure a perfectly ventilated roof.
The ISOTEC® panels can be laid properly thanks to their interlocking shape , thus providing a state of the art surface that avoids cold points.
|
|
|
Roof is the most exposed element of a facility. It should defy changeable weather conditions, assure water-resistance, and offer protection against cold in wintertime. Simultaneously it shall prevent overheating of the attic rooms in summer time and assure low level of transmission thermal losses in time of winter heating of attic rooms.
|
|
Produced description
Rigid panel in rock wool to high density, resistant to jam, calpestabile, not covered for the thermal insulation and acoustic.
Applications
Isolation to the upper wing surface of roofings flat (warm roof) and tilted.
Flat roofings: it is recommended for applications in which the impermeabilizzazione it is realized with liners or bituminous girdles also in case of absence of mechanical implantations (incollaggio).
Slanted roofings: particularly indicated in the event of roofs in wood and ventilated where it brings a meaningful increment of the acoustic performances.
|
|
Produced description
Rigid panel in rock wool to double density, resistant to jam, calpestabile, not covered for the thermal insulation and acoustic.
Applications
Isolation to the upper wing surface of slanted and flat roofings (warm roof).
Slanted roofings: particularly indicated in the event of roofs in wood and ventilated where it brings a meaningful increment of the acoustic performances.
Flat roofings: it is recommended for applications in which the impermeabilizzazione it is realized with liners or bituminous girdles.
|
|
|
Rigid rockwool panel, not covered, of high mechanical strength. Rigid rockwool panel, not covered, of class of compressibility B. Solution for inaccessible roofings including the ways of circulation. Heat insulation support of sealing under heavy or mechanically fixed protector.
|
|
|
Rigid, fire safe stone wool slab with high thermal insulation performance and load bearing capacity.
|
|
Rigid, fire safe stone wool slab with high thermal insulation performance and load bearing capacity.
|
|
Very rigid, fire safe stone wool board with high thermal insulation performance and load bearing capacity.
|
|
|
With a pressure resistant, self-supporting and form-stable structure Conlit® Steelprotect board defies the fire.
|
|
|
With a special waving fibrous structure, two different seals in the thickness %u2013 of a pressure resistant lower side and a step-firm hard printing distribution layer, is PRIMA ONE the ideal insulation for the flat roof. A raster marking facilitates besides a cutting.
|
|
Sarking and sheathing board made of natural wood fibre for roof, wall, and floor constructions
Sheathing board for pitched roof
Insulated wall panel made from natural wood fibre
|
|
|
IKO Wood Fiber Roof Insulation Standard Coated is composed of interlocking cellulose fibers bonded together by heat, pressure and premium asphalt emulsion. It is manufactured in a convenient, labor-saving board size of 2'''' x 3.96'''' (0.61 m x 1.21 m). This product conforms to all requirements of CSA A247 and CAN/ULC-S706. It has been UL/ULC classified under file R-16377/CR2818, and Factory Mutual approved.
|
|
|
Solid heat insulation made of natural wood fibre for top roof insulation
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Approximately 85% of all heat loss occurs through evaporation: an Ocea® cover can greatly reduce this loss.
Ocea®covers are used equally for indoor and outdoor pools.
Aqua Technology produces solar heating covers for outdoor pools - which capture the sun's energy, transferring heat to raise the water temperature by several degrees on a fine day.
CHEMICAL SAVINGS
The cover reduces consumption (and therefore, cost) of pool chemical additives due to minimizing evaporation and contamination of the water by organic garden debris.
FACILITY
The cover is operated electronically by the turn of a key.
SAFETY
The slatted cover is not considered to be a safety cover, however, through buoyancy it will support, for example, the weight of a domestic pet animal. Designing a safety ledge or handrails into the pool can enhance the safety factor.
AESTHETICS
Aqua Technology provides the broadest range of colours in Ocea® covers, chosen to harmonise with the pool lining and surroundings.
Photograph of our colour range of slats
|
|
|
|
