|
|
The heaters of the IGRAF family are used for surface heating and for fluid heating.
•HEATING AND DRYING of marble slabs, of resin surfaces, of scrap iron.
•Suitable to be incorporated in all exsiccation and drying ovens for wood and other materials.
•HEATING OF FLUIDS for industrial degreasing, for food cooking.
|
|
SlimKon façade heating systems
Today architects are designing more and more buildings with glazed façades. The heat requirement in the building is relatively easy to meet but managing the cold air around the perimeter is a more difficult problem: the heat losses around the perimeter cause air movement und can lead to unpleasant cold draughts.
Conventional heating systems are expensive to install and not always desirable from an architecural point of view. The solution? The SlimKon façade heating system effectively yet unobtrusively produces a "screen" of warm air in front of the glazing.
Features
effective screening, even at mezzanine level - comfort right up to the external façade
unobtrusive - fits into the interior architecture
convection heating prevents substantial energy losses - energy-saving!
highly-efficient
simply to install and maintain; ideal for retrofits
wide range of styles and finishes to meet individual design requirements
neutral in design; dimensions to suit
|
|
|
The HELIOS unit heaters, built with the same criteria of sturdiness and safety that define all Sabiana products, stand out for the splendid new design of the casing, made using anodised aluminium bars and polished die-cast corners. They have the same big heart as the Atlas unit heaters: a coil that has been conceived, designed and manufactured specifically for heating industrial environments. The thickness of the pipes, steel as standard, the diameter (Ø 22 mm) and the excellent ratio between the flow-rate of air and the heat output guarantee long life and exceptional comfort.
|
|
|
The Atlas unit heaters have a big heart: a coil that has been conceived, designed and manufactured specifically for heating industrial environments. The thickness of the pipes, steel as standard, the diameter (Ø 22 mm) and the excellent ratio between the flow-rate of air and the heat output guarantee long life and exceptional comfort. The Atlas unit heaters are made in 10 sizes, with heat outputs from 5 to 120 kW, and are available with 1 row coils for steam or high-temperature water systems, 2 row coils for hot water systems and 3 row coils for low-temperature hot water systems. They can be installed on the wall and on the ceiling.
|
|
The range of helicoid aerotherm consists in 7 different models used either in heating or cooling mode.
These equipment are intended to large volume buildings, store house, garage, workshop…
Aircalo aerotherm enables rapid heating or cooling volumes at the same time, mixing the air sufficiently to prevent its stratification (it is possible to complete this mixing by using zephir air recyclers).
Depending upon the characteristics of the building to be equipped, the Aircalo aerotherm may be hung (vertical blowing) or wall mounted (horizontal blowing).
|
|
HELIOTHERME H 4000 Air heaters
Range :
Available in 5 sizes depending on the cooling/heating capacity (from 4 to 155 kW) and the flow (from 1700 to 11000 m3/h) to be supplied
Available with casing:
Epoxy Polyester Coating
STAINLESS STEEL
Available with coil:
HERESITE coating
STAINLESS STEEL Tubes
ATEX variant (certified by an independent organisation: LCIE) for High and Low pressure water and Steam versions.
Heating capacity (LP Water): From 13 to 130 kW
Chiller capacity (LP Water): From 4 to 22 kW
Heating capacity (Water or HP Steam): From 32 to 155 kW
Electrical power: 9.6 kW, 18.9 kW, 28.8 kW or 43.2 kW
Flow: from 1700 to 11000 m3/h
Use :
The HELIOTHERME 4000 is an economical technical solution for heating premises by the ventilation of warm air in winter and cooling by the circulation of fresh air in summer.
The range meets APSAD and NFPA recommendations on air velocities around the edge of the units.
These air heaters are designed for use in all types of premises, from small to large spaces, for heating and cooling thanks to external production of warm or cool air.
- Shopping centres: hypermarkets, DIY stores or garden centres- shopping centres etc.
- Industry: workshop, storage depot, logistics platform etc.
- Administration: leisure centres, gymnasium, municipal depots etc.
In industrial processing, this air heater can be used as a drycooler (oil, thermal fluid etc).
|
|
|
The radiators are equipped with a kit for fixing them to the wall and with an air valve. Chromate radiators NOT available. Testing pressure: 10,5 bar - Working pressure: 7 bar. The watt values are not definitive awaiting for DeltaT50 certification.
|
|
|
The radiators are equipped with a kit for fixing them to the wall and with an air valve. Chromate radiators NOT available. Testing pressure: 10,5 bar - Working pressure: 7 bar. The watt values are not definitive awaiting for DeltaT50 certification.
|
|
|
|
