|
|
|
An immediately loadable ceiling, which permits any type of floor construction and simultaneously provides a visible quality ceiling ready for use, can be assembled in record time using the Profidecke. The high level of pre-assembly and the perfect fitting accuracy of the individual elements enable rapid laying on the building site. The short assembly time and easy of machining mean that the Profidecke element is a cost-effective, environmental alternative to conventional reinforced concrete ceilings and wooden beam ceilings.
|
|
|
K1multiplan is interesting in its conceptual design: Professionals appreciate the versatility of the product's many uses. K1multiplan becomes an important part of the structural design itself: Not only is it decorative but it can also take on load-bearing, bracing and space enclosing functions. K1multiplan satisfies individual requirements effortlessly.
|
|
|
The panel Wenus® is a new structural system, which can be employed horizontally or vertically for slabs, walls or covering. It is based on the use of raw or planed boards, which are screwed together obtaining the "W"-shape. Thereby a static height is accomplished, which confers a rigidity for free spans of 3 to 6 m.
|
|
|
Glulam is a high-quality material which is useful in a wide range of applications and possesses outstanding properties. It can be incorporated ideally in interior design and is particularly attractive.
|
|
|
The advantages of NORDLAM »ExpressElements« ceiling components are obvious. Simple and quick assembly is possible using the Rampa fittings which are included with the sections. The ceiling can be walked on as soon as it has been installed. The stability is therefore not compromised and the appearance of the underside is excellent. Depending on the application, the underneath can be left as a visible ceiling. From an environmental point of view, wooden ceiling constructions create a very pleasant climate in the room. Installations, even refits, are no problem.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
Our natural wood panels are the result of many years' experience in the wood working industry.
Our use of modern, environmentally friendly techniques, as well as systematic quality assurance at all production stages from logs to completed panel, guarantees a consistently high level of quality.
|
|
ELYCOP® is a sandwich pre-fabricated roofing system, insulating and self-bearing, precurved to a fixed radius of 3.30 m.
The modular elements create an opaque roof, diffused shed light interrupted by ELYPLAST® (C496) double-walled skylights.
ELYCOP® is used on pre-fabricated structures with alternating wing-shaped or Y beams, to create a light, dependable and functional roof.
|
|
Polyurethane foam inserted between the support, gives a perfect insulation between membership and the support.
Sheet steel with hot galvanizing second EURONORM 142-79. Phosphatizing treatment for better protection to oxidation. Painting consists of a layer of primer and a film of acrylic paint (or PVDF)on the surface outwardly a layer of primer act promote accession of polyurethane to the inner surface.
|
|
Expanded Polyurethane inserted inside the support, confers a perfect isolation and adherence within the support.
Sheet stainless steel AISI 304 or316. Treatment of inner surface with a special machining of promoting the adhesion of polyurethane.
|
|
Expanded Polyurethane inserted inside the support, confers a perfect isolation and adherence within the support.
Sheet steel with hot galvanizing second EURONORM 142-79. Phosphatizing treatment for better protection to oxidation. Painting consists of a layer of primer and a film of acrylic paint (or PVDF)on the surface outwardly a layer of primer act promote accession of polyurethane to the inner surface.
- 3 Greek tightening
- wide range of surface finishes
- ideal for roofing
|
|
Polyurethane foam inserted between the support, gives a perfect insulation between membership and the support.
Sheet steel with hot galvanizing second EURONORM 142-79. Phosphatizing treatment for better protection to oxidation. Painting consists of a layer of primer and a film of acrylic paint (or PVDF)on the surface outwardly a layer of primer act promote accession of polyurethane to the inner surface.
|
|
Mineral fibers
Sheet steel with hot galvanizing second EURONORM 142-79. Phosphatizing treatment for better protection to oxidation. Painting consists of a layer of primer and a film of acrylic paint (or PVDF)on the surface outwardly a layer of primer act promote accession of polyurethane to the inner surface.
|
|
Polyurethane foam inserted between the support, gives a perfect insulation between membership and the support.
Sheet steel with hot galvanizing second EURONORM 142-79. Phosphatizing treatment for better protection to oxidation. Painting consists of a layer of primer and a film of acrylic paint (or PVDF)on the surface outwardly a layer of primer act promote accession of polyurethane to the inner surface.
|
|
|
|
see the results for the following category : 
