|
|
|
An immediately loadable ceiling, which permits any type of floor construction and simultaneously provides a visible quality ceiling ready for use, can be assembled in record time using the Profidecke. The high level of pre-assembly and the perfect fitting accuracy of the individual elements enable rapid laying on the building site. The short assembly time and easy of machining mean that the Profidecke element is a cost-effective, environmental alternative to conventional reinforced concrete ceilings and wooden beam ceilings.
|
|
|
K1multiplan is interesting in its conceptual design: Professionals appreciate the versatility of the product's many uses. K1multiplan becomes an important part of the structural design itself: Not only is it decorative but it can also take on load-bearing, bracing and space enclosing functions. K1multiplan satisfies individual requirements effortlessly.
|
|
|
The panel Wenus® is a new structural system, which can be employed horizontally or vertically for slabs, walls or covering. It is based on the use of raw or planed boards, which are screwed together obtaining the "W"-shape. Thereby a static height is accomplished, which confers a rigidity for free spans of 3 to 6 m.
|
|
|
Glulam is a high-quality material which is useful in a wide range of applications and possesses outstanding properties. It can be incorporated ideally in interior design and is particularly attractive.
|
|
|
The advantages of NORDLAM »ExpressElements« ceiling components are obvious. Simple and quick assembly is possible using the Rampa fittings which are included with the sections. The ceiling can be walked on as soon as it has been installed. The stability is therefore not compromised and the appearance of the underside is excellent. Depending on the application, the underneath can be left as a visible ceiling. From an environmental point of view, wooden ceiling constructions create a very pleasant climate in the room. Installations, even refits, are no problem.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
|
|
|
|
Cross-laminated timber (KLH) is produced from spruce strips that are stacked crosswise on top of each other and glued to each other. The PEFC certificate guarantees that the raw material used comes from ecological, economical and socially responsible forests.
The crossways arrangement of the longitudinal and crosswise lamellas reduced the swelling and shrinkage in the board plane to an insignificant minimum - static strength and shape retention increase considerably. Compared to conventional timber construction products, cross-laminated timber offers entirely new possibilities when it comes to load transfer. Not only can loads be transferred in one direction (as is the case, for example, with supports, girders, etc.) but on all sides (referred to as "genuine plate and sheet action").
Only technically dried wood with a wood moisture of 12% (+/- 2%) is used to produce KLH solid cross-laminated timber boards. This rules out any damaging pest, fungus and insect attacks. All boards used are subject to a visual and mechanical quality sorting procedure.
The gluing takes place using solvent-free and formaldehyde-free PUR adhesive from Purbond (HB 110, HB 530) - this adhesive is tested according to DIN 68141 and other strict criteria of the MPA Baden Württemberg, Otto Graf Institute Stuttgart and is recognised for the production of internal and external supporting timber components and special construction methods in accordance with DIN 1052 and EN 301. The glue is applied automatically over the whole surface - the percentage of adhesive is 0.2 kg/m² and glue seam. A very high-quality level of adhesion is achieved as a result of the pressing power of approx. 6 kg/cm2.
The factory cutting and beaming of KLH solid cross-laminated timber boards takes place using state-of-the-art CNC technology. The basis for the cutting is formed by the cutting plans of the client. On request and with the appropriate equipment, the boards can also be cut by the relevant construction company.
|
|
Making yourself comfortable in a cosy living and working room panelled with solid wood.
In the living-room, in the bed-room, in the kitchen, in the office, on your balcony, on the stairs. You bring your ideas, we bring our experience in timber processing.
Construction of industrial buildings
|
|
Our natural wood panels are the result of many years' experience in the wood working industry.
Our use of modern, environmentally friendly techniques, as well as systematic quality assurance at all production stages from logs to completed panel, guarantees a consistently high level of quality.
|
|
Panel consisting of a layer of mineralised fir wood-wool bound with Portland cement coupled to a layer of expanded polystyrene of a guaranteed quality.
- Insulation of attic and loft floors
- Insulation of flat and sloping roofs
- Insulating wall covering for basements and arcades
|
|
Sandwich panel consisting of two layers (5 mm thickness each) in mineralised fir wood-wool bound with Portland cement, coupled to an internal layer of expanded polystyrene of a guaranteed quality.
- Acoustic insulation of walls
- Elimination of thermal bridges in pillars, beams, inter-storey facings, radiator niches
- Insulating wall covering for basements and arcades
- Insulation of roofs above and below the beams
|
|
|
|
|
|
The Unidek Condor Structural Insulated Roof Panel System not only provides the MMC solution to roof insulation but offers the added benefit of enabling the cost-effective creation of third storeys or rooms in the roof. The panel core is manufactured from EPS, sandwiched between two timber skins to form a highly engineered composite element. The combination of a highly developed sandwich technique with high load-bearing capacity and a comparatively low weight allows for free spans of up to 6 meters unsupported.
The system allows efficient, safe and fast installation, whilst providing a weather tight environment for following trades and for the structure below. The integral insulation also means that the panels will give the required thermal resistance to ensure an efficient roof element and can improve on traditional methods of providing thermal insulation significantly.
Unidek Condor SIRPS also offer a significant contribution to the overall SAP rating as the reduction in carbon emissions is achieved by the extremely low U-values achievable for a pitched roof - 0.16W/m2K for a 245mm thick panel.
Unidek Condor SIRPS significantly improve sound reduction and air leakage resistances over traditional roofing materials.
The impact sound is also reduced from rain and hail due to the composite action and design of the panels. Unidek Condor Daylight Panels can be supplied ready to receive a rooflight.
These panels are trimmed around the opening and have been structurally designed to spread the loads across the full element.
The Green Building Guide gives a rating of %u2018A+%u2019 for the panels with reclaimed slates, clay tiles and concrete interlocking tiles.
|
|
Celenit E3, thermal and acoustic insulation panel, in compliance with the norm ONES EN 13168, composed from two layers (5 thickness milimeter everyone) in wool of wood of red fir, mineralized and tied with Portland concrete of not inferior compressive strength to 42,5 N/mm2, and from a expanded inner shell of polistirene extruded autoestinguente, in compliance with the norm ONES EN 13164, produced from certifyd company ONES EN ISO 9001:2000. The panel is classified of Euroclasse and reaction to the fire.
Dimensions of the panel: cm 200x60
Thickness of the panel: milimeter 25, 35, 50, 75, 100
It employs: elimination of thermal bridges in pillars, architraves, cordoli solai, niches radiators; cantinati, porticati coating insulation of; isolation of roofs over and under the beams.
|
|
Celenit G3, thermal and acoustic insulation panel, in compliance with the norm ONES EN 13168, composed from two layers (5 thickness milimeter everyone) in wool of wood of red fir, mineralized and tied with Portland concrete of not inferior compressive strength to 42,5 N/mm2, and from a expanded inner shell of polistirene sinterizzato autoestinguente containing grafite particles, in compliance with the norm ONES EN 13163, produced from certifyd company ONES EN ISO 9001:2000.
The panel is classified of Euroclasse and reaction to the fire.
Dimensions of the panel: cm 200x60
Thickness of the panel: milimeter 25, 35, 50, 75, 100
It employs: elimination of thermal bridges in pillars, architraves, cordoli solai, niches radiators; cantinati, porticati coating insulation of; isolation of roofs over and under the beams.
|
|
|
Insulating panels with integrated wood furrings are used to insulate walls and garage ceilings. For new construction or renovations these panels will make insulation and gypsum board installation easy. In fact, the wood furrings are placed every 16%u201D providing a surface for screwing and allowing for quicker installation.
|
|
|
Parklex 3000 is a high-density stratified timber panel, impregnated using our exclusive Gureprex system. It may be adhered to any type of support material (fibreboard, MDF, fibre cement, galvanised steel etc.) normally used to construct full access floors.
|
|
| ... products without information |
| |
|
|