|
|
| This wall lamp keeps the design of its predecessor but with some reduced measurements that makes them ideal for exterior and interior low-level use. Available in direct or indirect light models, with symmetric, asymmetric and parallel reflectors. The energy threshold is from 70 to 150W for metal halide lamps, from 300W for lineal Halogen and 2x32W for compact fluorescent lamps. Manufactured in injected aluminium with grey polyester paint and with a protection classification of IP-65. |
|
Swiwel wall lamp diffused light in resin, diffuser of polycarbonate, for fluorescent bulb.
colour:
black
silver
white
light source:
fluorescent
structure:
resin
diffuser:
polycarbonate
bulb:
1x2D 21W GR10Q F
dimensions:
width: 26
height: 11
diameter: 22
depth: 30 |
|
Description: Archer Wall Washer
Finish: Sarin Bronze
Glass: Clear
Light: 1 Lt x 5w LED
Voltage: 12v |
|
| LUMINAIRE: In L-2520 cast aluminium. The closure is a 4 mm thick circular armoured glass, with a rubber profile and secured to the screen by five stainless steel staples. STAND: Made out of a 4 mm thick DIN 2440 steel tube, 3" in diameter, all protected by a rust-proof coating (dichromated). NUTS AND BOLTS: In A4 stainless steel. |
|
Housing and front frame: In diecast aluminium.
Diffuser: In tempered glass, thermal shock and impact resistant.
Reflector: In high-grade die-cut and folded 99.85 aluminium.
Painting: In several stages. First stage: black epoxy cationic electrocoating, resistant to corrosive and saline environments. Second stage: UV-stabilizing primer, and lastly rough finish with graphite acrylic coating.
Lampholder: In polycarbonate, with phosphor bronze contacts (FLC). In ceramics with silver-plated contacts (SAP-E - MBF).
Electric gear: 230V/50Hz supply with thermal protection (except versions FLC/MBF/SBP). Hard wire, cross-section 0.50sqmm (FLC), PVC-HT sheath, or silicone wire terminated with quick-connection admiralty brass clamps; double fibreglass braid insulation. 2P or 2P+T terminal block (maximum allowed lead cross-section: 2.5 sqmm).
Standard supply: When open, the front frame stays attached to the housing by means of safety springs, for easy maintenance.
Equipment: Gasket in environment-friendly material. Waterproof rubber cable gland Ø 1/2 gas thread (cable min. Ø 9 max. Ø 12).
Regulations: Produced according to applicable EN60598-1 CEI 34 - 21 standards, IP65IK07 degree of protection to EN 60529 standards. This product can be installed on normally inflammable surfaces. |
|
Die cast aluminum up/down wall light interior/exterior.
Marine grade corrosion resistant heavy walled high pressure die cast aluminum construction. Ballast box is included with all HID lamps. |
|
Dimensions:
8 3/4" W 20" H
9" Die cast aluminum up/down light cylinder.
Marine grade corrosion resistant heavy wall high pressure die cast aluminum construction, with die cast back mounting plate. |
|
Die cast and extruded aluminum linear fluorescent wall wash.
Housing is one piece extruded aluminum with cast aluminum ends. Supported by die cast aluminum swivels with locking teeth and 1/2" N.P.T. for mounting with die cast canopies. Available for exterior or interior applications. |
|
Dimensions:
5-7/8" W x 10-7/8 H
6" Diameter die cast aluminum downlight surface mount cylinder.
Marine grade corrosion resistant heavy wall high pressure die-cast aluminum construction, with die-cast back mounting plate amd extruded aluminum body.
Available as a downlight wall or pendant. |
|
Dimensions:
7 1/4" W 13" H
Large diameter die cast aluminum down light surface mount cylinder.
Marine grade corrosion resistant heavy wall high pressure die cast aluminum construction, with die cast back mounting plate and extruded aluminum body. |
|
Dimensions:
10" Dia
Exterior die cast architectural bulkhead.
Marine grade corrosion resistant heavy walled high pressure die cast aluminum construction. |
|
Dimensions:
5 7/8" W 18 1/2" H
6" Diameter die cast aluminum up/down light cylinder
Marine grade corrosion resistant heavy wall high pressure die cast aluminum construction, with die cast back mounting plate and extruded aluminum body. |
|
Dimensions:
15" W Side View 15" H Bottom View
Die cast aluminum exterior architectural wall or post mount.
Marine grade corrosion resistant heavy walled housing, lens frame and mounting plate, high pressure die cast aluminum construction. |
|
Exterior architectural semi recessed indirect wall mount.
Corrosion resistant heavy gauge CRS. Die formed and seam welded for solid construction with die cast aluminum integral socket assembly. |
|
Dimensions:
7 1/4" W 20" H
Large diameter die cast aluminum cylinder, up/down wall mount w/2 lamps.
Marine grade common resistant heavy wall high pressure die cast aluminum construction, with die cast back mounting plate and extruded aluminum body. Back box included for HID unit, die cast. |
|
Dimensions:
9-1/4" W Side View 10-1/2" H Bottom View
Die cast aluminum exterior architectural wall or post mount.
Marine grade corrosion resistant heavy walled housing, lens frame and mounting plate, high pressure die cast aluminum construction. |
|
Die cast aluminum exterior wall mount.
Marine grade corrosion resistant heavy walled housing, and lens frame, high pressure die cast aluminum construction. Die cast looking swivel, tilts 12 degrees. |
|
Dimensions:
18-1/2 W x 7.25 H
Shadow-free ADA half round wall sconce for wet locations.
Heavy gauge aluminum back housing seams are welded and polished, fitted with heavy gauge aluminum bar stock guard. Tamper proof stainless steel fasteners. |
|
Dimensions:
8 3/4" W 14 1/4" H
9" Die cast aluminum cylinder surface, pendant or wall mount.
Die cast aluminum housing and baffle. |
|
Slimline Wall Pack (SLWP)
HPS / 100 - 400 watts
MH / 175 - 400 watts
PS / 200 - 400 watts
Applications:
Parking facilites, entry ways, perimeter or pathway
lighting, or underpasses.
Features:
Die cast housing with side conduit access
Textured Bronze Finish
Borosilcate molded prismatic glass lens
1/2" threaded apertures for conduit and photo control
Hinged door frame for easy relamping
Lamp Included |
|
| The extraordinary simplicity of the Moove series for interiors, characterised by the stereometric use of sleek lines, is available in the IP65 version conceived to ensure the greatest degree of protection from the elements. Further simplified in order to match the typical characteristics of exterior spotlights, the new Moove IP65 stands out as one of the most compact asymmetrical direct, indirect light fixtures on today's market. The unobtrusive design of the diecast aluminium body and a simple system of rotation enable the fixture to swivel and make it highly flexible, minimising the visual impact on the architecture. |
|
Provence
Design: Hans Gabriel Finne
The design of the Roulette family makes it suitable for modern and classical houses and gardens. This series has post fittings with one, two or three lamps and wall-mounted fittings in various sizes. Short posts and gatepost mountings are also available.
In addition to Provence Roulette II and Roulette III make the Roulette family.
|
|
Atrium III
Design: Hallvard Jacobsen
Light is important in any environment, both by day and by night. The colour, shape and lines of the fitting, as well as the light it produces, affect our senses and enhance our experience of the environment
Atrium III provides light and design of the highest quality, and suits all types of environment. Thanks to a wide assortment of light sources and efficient reflectors, it is easy to adapt the function of the fitting to all sorts of applications.
|
|
OptiFlood MVP506
Philips Lighting's long tradition of asymmetric floodlight excellence. The optical system ensures peace of mind for the client by providing an accurately controlled, low obtrusive light installation. OptiFlood floodlights with precisely controlled light distributions can effectively counter light pollution: a total light cut-off above the horizontal and a peak beam intensity at high angles. Accommodates metal-halide lamps for good colour rendering or high-pressure sodium lamps for economical operations.Available with two types of reflectors: asymmetric or road lighting POT optic. |
|
| Extruded aluminium body, cataphoresis treated and powder-painted in grey Coron. Cast aluminium locking rings. A4 stainless steel screws. 5 mm tempered glass cover. Fixed to the wall with a special bracket. Also available in black and white. Versions for other types of lamps are available on request. Electric connection by quick clamp. |
|
FARO
Wall-mounted luminaire FARO, for 1 x compact lamp 18W with lampholder 2G10, in aluminium, light silver, opal polycarbonate diffusor, protection class I, protection degree IP54, with electronic control gear, B = 160mm, H = 288mm, A = 98mm |
|
| The VPR Optic - Vertical Parking Roadway - have a beam with ample side emission and asymmetrical distribution towards the roadway. The tilted position of the lamp holder and flow recovering device in a central position guarantee high levels of efficiency and maximum uniformity on a horizontal and vertical plane. This is the ideal solution for street lighting in various dimensions where it is necessary to maintain elevated distances between the poles to guarantee high levels of brightness and uniformity. |
|
H100
TMS classic anodized H100 9"Diameter Sign Light in Compact Fluorescent, Metal Halide & Incandescent.
-Aluminium Construction
-Available with an Electronic Direct or Remote Mount Ballast(unless noted)
-Choice of CF42w, MH70w or INC150w( CF & MH Lamp included)
-Available ONLY in anodized
-Wire Guards & Globes |
|
- Available with LED & MR16 halogen lamps.1 Lamp info: LED, MR16.
- Precision machined from aluminum, brass, or stainless steel with all stainless steel hardware.
- Removable cap available in four cutoff styles.
- Each cap holds up to three lens accessories.
- Various mounting canopy options allow for surface mounting or mounting on industry standard round and rectangular junction boxes.
- Requires mount with transformer option or remote transformer.+
-Distributors wanted.
Available in 14 standard colors as well as several aluminum, brass, and stainless steel metal finishes.
CSA tested & certified to US & Canadian safety standards wet location wall mount use. |
|
|
|
Urban lighting: wall lights
