Wooden structure connectors

The Simpson Strong-Tie RCKW rigid connectors have been developed to resist overturning moment at the base of exterior kneewalls and parapets as well as interior partial-height walls. The RCKWS is a heavy 7-gauge stiffener ...

... Stronger than angled nailing or screw fastening alone for outdoor living or home repair projects Install with Outdoor Accents connector screws for decorative look and maximum strength (sold separately) Material APVA4, ...

The Simpson Strong-Tie® Outdoor Accents line of decorative hardware features connectors and fasteners that bring beauty and strength to custom outdoor living structures. The deck joist tie attaches 2x ...

... features connectors and fasteners that bring beauty and strength to custom outdoor living structures. The Avant Collection features straighter edges for a more contemporary design. These gable plates ...

Outdoor Accents flat T straps from Simpson Strong-Tie bring decorative appeal and lateral strength to any outdoor living space. They provide reinforcement for a connection where one lumber piece intersects another at a 90° angle. This ...

... x 3" Strong-Drive® SDS Heavy-Duty Connector screws, which are supplied with the URFP. For URFP, alternate lag screws will not achieve published loads. FRFP shall use a minimum Strong-Drive SDS Heavy-Duty Connector ...

CBTZ is part of the concealed structural connector line that combines structural strength with invisibility. Designed to connect horizontal beams atop a vertical post, the CBTZ continues the structural load path into ...

... a minimum of 1/32" to a maximum of 1/16" larger than the bolt diameter (per 2015 NDS, section 12.1.3.2) Contact engineered wood manufacturers for connections that are not through the wide face Options Straps may ...

... x 2 1/2" Strong-Drive SDS Heavy-Duty Connector screws, which are provided with the column cap. (Lag screws will not achieve the same load.) Install stainless-steel Strong-Drive screws with stainless-steel connectors. CCOQ ...

Column-to-beam connections often have multiple beams framing on top of a column. L, T and cross-column caps provide design solutions for this application. Material 7 gauge Finish Simpson Strong-Tie gray paint; also available in ...

... CONCEALED JUNCTION The pair of connectors at a 45° angle guarantees a highly resistant and rigid retractable junction, protected from fire and appropriate for earthquakes COUPLING The total thread of the connector ...

... classes 1 and 2 MINIMUM DISTANCES Special approval for use of the connector with reduced minimum distances and hence on smaller beam widths HIGH SLOPES Special approval for use of the connector parallel ...

Double thread connector for insulation Carbon steel with white galvanic zinc coating PACKAGING Box + CE paper + BIT CONSULTING Free myProject software and personalised consultations to optimise fastenings CYLINDRICAL ...

Double thread connector for insulation Carbon steel with durocoat TEMPLATE Cardboard template in each box for proper placement of the fastenings CONSULTING Free software and personalised consultations to optimise fastenings OPTIMISED ...

... classes 1 and 2 STEEL – WOOD The use of the connector inclined at 45° in combination with a steel plate guarantees high sliding resistance and rigidity of the joint LIFTING The connector ...

... Service classes 1 and 2 LARGE STRUCTURES The lengths of the connector allow for the creation of very large structural solutions, such as coupling of very high beams and joints on large structures FAST ...

... or 5 mm (2 and 3 plates). Can be used with screwdrivers with 1500 rpm minimum. Service classes 1 and 2 RIGID JOINTS The connectors allow for the creation of rigid joints able to transfer bending moment stresses (moment-resisting ...

... classes 1 and 2 FLOOR SLAB The connectors placed at 45° in an “X” configuration make it possible to obtain perfect coupling and excellent static performance between the concrete slab and the wood beams INSTALLATION The ...

ALUMINUM BRACKETS WITHOUT HOLES Rapid fastening thanks to the use of HBS+ screws The optimum choice for narrow sections (trellises, gazebos,…)

ALUMINUM BRACKETS WITHOUT HOLES Rods 2.20 m long to be cut according to building site needs For wood - wood and wood - concrete connections

... stress in the connection Exceptional mechanical strength Better sustainability of structures Controlled fire resistance Improvement of the lifespan of the structure (no slot and drilling) Resin ...

... galvanised connector plate is used in the manufacture of the majority of the trussed rafters that our customers manufacture. The appropriate sized plate is specified by our sophisticated design software and is then ...

... the increased depth of the timber members and higher forces being transferred through the timber joints. A typical MiTek attic truss design might include a mix of M20 and B90 connector ...

This 2mm glavanised plate is typically used in large span, commercial roofing applications. In the domestic roofing market, trussed rafters have long been the construction method of choice for the UK and Irish construction industry. ...

... transportation of the truss. The plates allow for the cap of the truss to be site fixed using nails through pre drilled holes in the connector plate. The number and type of nail used in the connection is important and ...

Hüttemann Engineering Timber is the term for high-quality timber. Free-spanned glulam structures allow for a wide variety of design options and flexibility. Industrial and commercial building production ...