A range of hoods exploiting the "inductive emission" principle. Untreated air is introduced inside to partly compensate for that removed. This results in better drawing of fumes towards the filter surface and reduced air-treatment costs. The range consists of hoods with 5 different lengths (2400, 2800, 3200, 3600 and 4000 mm) and 3000 mm deep.
- All stainless steel construction
- Exhaust air volume control dampers
- Adjustable exhaust chamber balancing baffles
- Full length intake slot and a series of full length extraction baffles within the exhaust plenum
- Continuous cold water mist during fan operation
- Daily hot water and detergent wash cycle
- Listed fire dampers if required
- Full access through front removable panels
- Available in lengths from 1000 mm to 3000 mm in 100 mm increments
- Flexible options and modifications
- All stainless steel construction
- Exhaust air volume control dampers
- Adjustable exhaust chamber balancing baffles
- Full length intake slot and a series of full length extraction baffles within the exhaust plenum
- Continuous cold water mist during fan operation
- Daily hot water and detergent wash cycle
- Listed fire dampers if required
- Full access through front removable panels
- Integral make-up-air plenum with removable ‘Perfair’ diffuser panels
- Available in lengths from 1000 mm to 3000 mm in 100 mm increments
- Flexible options and modifications
- High-efficiency grease filtration using UL- and NSF-classified KSA multi-cyclone filters - removing up to 95% of particles with a size of 8 microns or above
- Exhaust airflow measurement and control using the in-built adjustment damper located in the extract spigot(s) and the T.A.B.™ testing and balancing tap
- Stainless steel (AISI 304), welded construction
- High-efficiency grease filtration using UL- and NSF-classified KSA multi-cyclone filters - removing up to 95% of particles with a size of 8 microns or above
- Exhaust airflow measurement and control using the in-built adjustment damper located in the extract spigot(s) and the T.A.B.™ testing and balancing tap
- Stainless steel (AISI 304), welded construction
A range of wall-mounted hoods used for snack applications and on the 700 and 900 series cooking units. Their particular profile and the limited installation height makes them suitable for use in places with low ceilings. The range consists of hoods with 6 different lengths (2000, 2400, 2800, 3200, 3600 and 4000 mm) and 2000 mm deep.
- All stainless steel construction from grade 304 satin-finish sheet
- All-welded construction
- An aluminium egg-crate-type extract grill with opposed blade damper in each extract spigot
- Integral make-up-air plenum with removable ‘Perfair’ diffuser panels
- Ease of installation, claning and servicing
- Available in lengths from 1000 mm to 3000 mm in 100 mm increments
- Flexible options and modifications
- All stainless steel construction
- High efficiency self draining centrifugal baffle type grease filters
- Flexible options, cleaning and servicing
- Available in single lengths 1000 mm to 3000 mm in 100 mm increments
- 3-sided stainless steel duct-cladding
- Integral make-up-air plenum with removal 'Perfair' diffuser panels
- Condensation is achieved by the use of angled internal baffles and deflectors
- Efficient exhaust is maintained by using lateral side slots combined with the large internal volume
- Modular construction simplifies design and installation
- Adjustment and measurement of airflow using the T.A.B. ™ measuring tap in combination with an adjustment damper within the extract spigot(s)
- Manufactured from polished stainless steel AISI 304
- Surface mounted light fittings are available as an accessory.
KWI - Capture Jet Canopy with Automatic Water Wash technology
Product main features
Automatic periodic cleaning of the exhaust plenum and KSA grease filters
Minimal maintenance requirements, reducing the work load for personnel cleaning the filters
High level of hygiene facilitated
Prevention of the build-up of grease deposits, which pose a serious fire hazard
UVF - Capture Jet Canopy with Supply Air and UV-technology
Product main features
- Integrated Capture Ray Ultraviolet cassette with complete controls and safety features.
- High efficiency Capture Jet technology reduces the exhaust air flow volume required.
- Draft-free air distribution directly into the working zone from the front face, low velocity supply diffuser.
- Capture Ray Ultraviolet cassette with integrated controls and safety.
- Easy access to UV cassettes for maintenance.
- Integrated Capture Ray Ultraviolet cassette with complete controls and safety features
- High-efficiency Capture Jet technology reduces the exhaust airflow volume required
- Capture Ray Ultraviolet cassette with integrated controls and safety
- Individually adjustable personal supply nozzles located in the front supply plenum help to reduce the effects of the radiant heat given off by the cooking equipment (optional)
Integrated or surface-mounted light fitting available (optional)
Option of a general exhaust module (GE) built into the side panel of the canopy if additional extraction from the kitchen area is required
High efficiency grease filtration using UL and NSF classified Halton KSA multi-cyclone filters - up to 95% removal of particles at a size of 8 microns or above
Exhaust damper located in the extract spigot(s)
Stainless steel, welded construction (AISI 304)
- Integrated or surface-mounted light fitting available (optional)
- Option of a general exhaust module (GE) built into the side panel of the canopy if additional extraction from the kitchen area is required
- High efficiency grease filtration using UL and NSF classified Halton KSA multi-cyclone filters - up to 95% removal of particles at a size of 8 microns or above
- Exhaust damper located in the extract spigot(s)
- Stainless steel, welded construction (AISI 304)
Commercial ventilation: extractors
