|
|
Type S
Blades 22-27-34-40-47-60 cm width, elliptical profile manufactured from pre- painted aluminium sheet 0,8-1,0-1,2 mm thick, reinforced inside by extruded aluminium "I" section. Shaped end blocks fit inside the louvre skin, manufactured from nylon or die-cast aluminium. The end blocks retain the "I" reinforcing position. Extremely high deflection resistance.
Maximum height of one louvre 3 metres for blades 22 cm, 4 metres for blades 34 and 40 cm, 6 metres for 47 cm, 8 metres for 60 cm.
Frames: natural extruded anodized aluminium, with more sections depending on the dimension of the blade and according to aesthetic needs. External connecting-bar in natural extruded anodized aluminium on bronze washers and inox nuts.
Controls: teleflex type manual control, with reducer or electrical linear action.
Colours: standard colours are white ral 9010 and silver ral 9006. We can supply all ral colours upon request
|
|
LINEA G
Blades: 44 cm in width. Manufactured from aluminium sheet from 8/10 up to 10/10 thick, pre-painted PVF or anodized, internally strengthened with structural ribs; the heads are of pressed aluminium or reinforced nylon. Max height 5,00 m.
Frames: natural extruded anodized aluminium, with more sections dependent on dimension of the blade and according to aesthetic needs; external connecting-bar in natural extruded anodized aluminium on bronze washers and inox nuts.
Controls: teleflex manual control type, with reducer or electrical linear action.
Colours: standard colours are white ral 9010 and silver ral 9006. We can supply all ral colours, upon request.
|
|
Whether for Smoke Control, HVAC or Solar Control, Colt Control Systems are specifically designed to meet the requirements of the project. Colt can provide all manner of electric, electronic and pneumatic controllers, panels and their necessary ancillaries.
All Colt Control Systems have been designed, manufactured and tested to all applicable Standards.
Programmable Controls include OPV 2000, ICS 4-Link and Soltronic.
Primarily intended for smoke control applications, OPV 2000 incorporates all smoke control equipment into a total addressable smoke control system. Click here for the leaflet (7.5 MB).
ICS 4-Link is a generic control system that can operate HVAC, smoke control and solar shading systems. It has a wide variety of operating modes, including sun tracking, daylight optimisation and PV illumination. The position of the sun is continually calculated by its intelligent processor while internal temperature and lighting sensors send signals to the processor, altering the position of the louvres in conjunction with the present readings. In this way the building can "react" appropriately to the sun's position and to the weather. Remote operation is available via an internal modem interface, and manual control or connection to a client building management system is also possible.
Soltronic is designed for the control of smaller solar shading systems. It is a simplified version of ICS 4-Link which can control up to 10 actuators in any zone. It responds to timers and sensors, and sets the optimum position of the louvres.
|
|
The Colt Shadotex system is a unique, alternative solar shading solution. The Shadotex system consists of a special fabric stretched between two sides of a louvre support frame. The fabric is manufactured with a weave to prevent solar glare and solar heat gain. The fabric can also create attractive diffused light and can allow high external vision.
The Shadotex system is given its strength by coating the fabric in a special resin which dries hard. This type of product is extremely lightweight which allows large spans to be constructed without the need for additional supporting framework.
This system offers building designers a unique solution to external solar shading systems.
Features & Benefits
Modern & unique design
Optional fabric choice
High solar absorption
High solar reflection
Lightweight construction - ideal for large spans
Good external vision
Unlimited colours
Easy to clean (resin/teflon coated)
|
|
Colt Shadoglass is a fixed or controllable external glazed solar shading system (glazed louvre system) that may be installed either vertically or horizontally in front of the façade.
This louvre system is also suitable as a primary or secondary facade element for ventilation.
It may be combined with other Colt products such as rooflights and glazed facades. Also Coltlite for glass louvre - natural glass louvred ventilators - could be of interest to you.
A Shadoglass controllable or fixed glass louvre shading system can reduce solar heat gain, lower air conditioning running costs, and lessen glare whilst maximising the use of natural daylight.
Shadoglass glass louvre shading systems are operated by linear actuators that have the capability to operate complete facades. The glass louvres are available in various colours, surface finishes and coatings to meet specific design requirements. Photovoltaic cells may be integrated into the glass louvres so as to obtain further energy benefits.
Please also see our Gallery and Projects pages for further impressions.
Types available
There are five standard systems in the Shadoglass range. The leaflet (pages 4-14) provides further information.
|
|
Colt Solarfin is a fixed or controllable external solar shading system that may be installed either vertically or horizontally in front of the façade.
It may be combined with other Colt products such as rooflights and glazed facades.
A Solarfin shading system can reduce solar heat gain, lower air conditioning running costs, and lessen glare whilst maximising the use of natural daylight.
With over 20 standard profiles, fins are available as one-piece extrusions in widths up to 400mm and as multiple clipped together extrusions in widths up to 1050mm.
The Colt Solarfin system comprises a series of extruded aluminium fins mounted into a support frame. The fins may be fixed at any angle and can rotate under motorised control. Fins are available as one piece extrusions in widths up to 400 mm and as multiple clip together extrusions in widths up to 1050 mm. Spans can be up to 6m without intermediate support and up to 10m with intermediate bracing rods. Fabricated and perforated fins are also available.
Colt has a wide range of standard profiles but bespoke profiles and designs can be developed on larger projects.
All principal components are manufactured from extruded aluminium alloy type 6063 T6 with stainless steel fixings. Controllable fins can pivot through 120 degrees and can be controlled by astronomical data operating the actuators to track the path of the sun.
|
|
TYPE HT
Blades: High Tech available in two models of 205 and 530 mm wide, manufactured with perforated calendared aluminium sheet (pitch, section and disposition of the holes are supplied upon request), with lateral bending to give rigidity, fixed to a light structure composed of a central tube in extruded aluminium and some brackets fixed to the supporting tube with non visible screws.
Supports, sea-gull-shaped in the 530 model and triangular shaped for the 205 model, are manufactured in aluminium and shaped to give physical and aesthetic lightness to the blade. At one of the extremities of the blade there are some connecting rods for the fixing of the movement system.
The dimensions of a complete blade 530 are: 530 mm wide and 97 mm thick for a variable length up to 5 mt; the 205 blades are: 205 mm wide, 55 mm thick and of a variable length up to 2,5 mt.
Frames: natural extruded anodised aluminium, with more sections depending on the dimension of the blade and according to aesthetic needs. External connecting-bar in natural extruded anodised aluminium on bronze washers and inox nuts
Controls: reducer or electrical linear action 220 V.
|
|
Colt Shadovoltaic is a fixed or controllable external glazed solar shading system that may be installed either vertically or horizontally in front of the façade. Photovoltaic cells are integrated into the glass so as to generate electricity.
It may be combined with other Colt products such as rooflights and glazed facades.
A Shadovoltaic shading system can reduce solar heat gain, lower air conditioning running costs, and lessen glare whilst maximising the use of natural daylight.
There are two standard systems in the Shadovoltaic range. Bespoke designs are also available to suit the requirements of almost any project.
Shadovoltaic shading systems are operated by linear actuators that have the capability to operate complete facades. The glass louvres are available in various colours, surface finishes and coatings to meet specific design requirements.
Construction
The principal support and control components are manufactured from aluminium and stainless steel. Aluminium extrusions are to BS 1474 Grade 6063 T6.
The panels are heat soak tested toughened glass with the edges treated to remove stress. Glass thicknesses of between 8mm and 16mm max are available. The glass specification will be tailored to suit each application, taking full account the project 's aesthetic and performance requirements.
Photovoltaic cells may be integrated into the glass, either laminated onto the reverse side of the glass panels or between the two sheets of a safety glass.
|
|
Outdoor wooden blinds
The exclusive discovery of facades dressed
with wooden slats which can be lift up and adjusted.
Softened sunlight for outdoor application
For your glass roofs and verandas.
|
|
DESCRIPTION
Among the building covering solutions available, the Atena Sunscreen staves are especially suited where local screening of direct light is required. Different effects can be obtained as desired, depending on the inclination of the crosspiece used.
TECHNICAL SPECIFICATIONS
External covering with ATENA SUNSCREEN type staves, obtained form profiling of aluminium strips pre-painted on one or both sides, thickness 6/10. Inclination of the staves at45°, 30° or 20° is provided by the various selection of support crosspiece realised by profiling of special aluminium alloy strips with a thickness of 10/10, painted white on both sides.
|
|
|
Faber venetian blinds with aluminium slats were introduced for the first time in 1949, and not many homes in Denmark have been without venetian blinds since, typically those in classic white.
|
|
Weight: appr. 6,0 kg/m² (1,23 lbs/sqft)
Open area: appr. 51%
Main applications: Facade, Ceiling, Space
the flat surface on one side of the EGLA-TWIN creates a reflection across the full plane
In the direction of the thinner twin wires the mesh is relatively flexible and can be easily adjusted to certain radii
|
|
HunterDouglas® Aerofoils are standard available in 6 different sizes and in an adjustable or fixed configuration. The specific fin design allows for larger spans and there is a choice of support structures.
FIXED FIN ANGLE
• The fixed fin support structure has been designed to accommodate any
angle between 0° and 180° with increments of 5 degrees. The fin angle
can be set during installation.
• Fixed fin V-bracket, available in 0, 30 and 45 degree for the 200 - 300AF.
• Fixed fin Cup-bracket, available in 0, 30 and 45 degree for the 350 -
450AF.
The adjustable Aerofoil system gives the user the option of setting the fins at any possible angle from 0 to a maximum of 120 degree at any time. With this motorised system, maximum convenience can be obtained with the optional intelligent control system, which automatically regulates the fins according to the sun path. The high quality materials guarantee this system to operate with a minimum of maintenance.
|
|
The Luxalon® 70S and 132S Sun Louvre system consist of sturdy Z-shaped panels. The panels are used to achieve a crisp Sun Louvre or façade and result in an aesthetically pleasing overall appearance.
• Roll formed aluminium panels of 70 or 132 mm wide
• Coil coated with UV and scratch resistant Luxacote® coating available in 14 standard
colours. Other colours on request.
• Stylish carrier rails with sliding brackets allow a variable module by which openness
and shading angle can be selected
• 70S and 132S panels can be combined on one support rail
• The Luxalon 70S and 132S system can be installed in three ways:
- Projected horizontally at the top of the glazed area or roof edge
- Positioned vertically
- Combination of horizontal and vertical
- Corner solutions available
• The vertical Luxalon® 70S and 132S sun louvres combine multiple
functions in a single product:
- The Z-shaped panels have been specially developed as a Sun Louvre
system for façades exposed to low sun angles
- It can also be used as ventilated façade system. Covering for example
installations on rooftops or staircases
|
|
Solar protection
Sun-break hung without altering the weather-proofing of the façade, by using inside frame gaskets.
Easily adapted to solar protection, using punctual pressure.
Choice of protection :
• "SCREEN" sun-blind
• Adjustable vertical louvers
• Fixed louver sun-break
• Combination aluminium louvers and "SCREEN" sun-blind
• guaranteed comfort and light control, whatever the position of the sun.
|
|
|
In either horizontal or vertical orientation, the EUROSLOT grille provides an original structure projecting lighting and shading effects
|
|
TYPE F
Sun protection composed of an aluminium profile. The system provides two types of blades:
- F1 is Z shaped;
- F2 is round.
Both F1 and F2 are 142 mm wide and are finished in either pre-painted aluminium on the external face (on both sides if requested) and in various colours. This system can be assembled very quickly and is extremely versatile. Versatility enables to chose the distance between blade centers (minimum distance 160 mm).
Additional blades must be supported every 1,5 to 1,8 m. Colours: standard colours are white ral 9010 and silver ral 9006. We can supply all Ral colours upon request
|
|
STOCKAL® is the Novelis brand name for its aluminium sheet pre-painted with polyester based liquid paints. STOCKAL® is eminently suitable for use in the building industry, especially for façade cladding and window flashings. The wide range of colours and the extraordinary workability of the aluminium substrate make STOCKAL® the most versatile material produced by Novelis.
STOCKAL® is characterised by an extraordinary degree of workability. Thanks to its chemical and mechanical characteristics, due to the combination of an EN AW 5010 alloy and polyester based liquid paints, STOCKAL® can be easily worked using the main mechanical working processes: bending, drilling, milling and cutting; these are only part of the standard working processes for STOCKAL®. The use of a special protective liquid coating on the reverse side also makes STOCKAL® suitable for gluing and bonding.
|
|
|
Continuous louvre system blade (pitch 150mm): sheet aluminium blade, perforated underside, packed with inorganic mineral wool for acoustic performance
|
|
Aluminium solar shading with aerofoil blades in fixed position
|
|
Aluminium solar shading with aerofoil blades is a DIY-kit ready to be installed
|
|
Vertical aluminium solar shading system with C-shaped blades clipping on a support structure
|
|
|
In order to control the thermal gain and the natural day light entry, Renson has developped the SUNCLIPS® Patio: sunshading aluminium sliding panels
|
|
Horizontal aluminium solar shading system with C-shaped blades clipping on a support structure
|
|
Brise Soleil
The Reynaers BS (Brise Soleil) system is an aesthetic and practical solution for nearly all new and existing buildings. It is available as a standard system or tailored solution. Brise Soleil is the general designation for a louver system that is secured to the outer façade and protects against heating and glare. BS systems are a budget-friendly way for architects to integrate more design modules into their designs and give their buildings that extra oomph. BS systems are available in various dimensions and types of fixed and moveable slats.
|
|
Direct sunlight causes glare and unwanted heat on window areas. Outlook Sunscreens are carefully designed and installed to deflect and eliminate this problem, without shutting off the outside view. Manufactured from durable aluminium, Outlook Sunscreens allow free movement of air around building exteriors and yet add a distinctive design element that can enhance a buildings appearance.
Webforge offers a comprehensive service for the design and manufacture of sunscreens, specifically for your project and budget.
Outlook Finishes
Outlook Sunscreens are available in a wide range of colours and can be anodised or powder coated. Special requirements in colour or finish can be catered for. Outlook Sunscreens can also be used in a natural mill finish.
Approved Testing
Extensive wind tunnel and impact testing by C.S.I.R.O., Monash University and the James Cook University has shown Outlook Sunscreens will meet the tough standards required for cyclonic and debris protection. The proven strength of Outlook also makes it an ideal security medium.
|
|
Lockline aluminuim screens enhance privacy as well as security in a myriad of applications both inside and outside the home. The modern stylish look of Lockline lends itself to today's designs and a wide range of finishes are available. Mill finish lends itself to the industrial look however where a softer look is required anodising and powder coating are both available. Powder coating is available in an extensive range of colours for both internal and external applications. With a range of options of aperture sizes and panel depths Lockline has proven its versatility in a wide variety of projects. Designed to reduce the effects of direct sunlight on a building façade Lockline sunscreens reduce energy consumption while at the same time providing a near uninterrupted view of the surroundings. Approximately one third the weight of an equivalent steel profile, Lockline aluminium sunscreens offer construction savings as they can be installed easily without the need for bulky support structures.
Lockline sunscreens can be installed vertically, horizontally or at any angle in between. When installed horizontally it is possible for the sunscreen to provide a dual role as both sunscreen and as a walkway for maintenance access or for window cleaning. Vertical screens on the other hand can be used to hide unsightly areas around the building including bin storage areas, plant and equipment locations and vehicle access ways. Lockline screens can be manufactured in individual panel sizes up to a maximum of 6m x 1.2m. Larger areas can be achieved by joining edge bars or extending the swage bars.
|
|
|
|
Solar shading
