Cast iron pumps

Flow: 43 m³/h
Weight: 38, 40, 44, 46 kg

Cast iron submersible pump : Drainage and Storm Water Pumping Can be installed in an existing manhole or pit Exists in 4 versions Cast iron submersible pump ...

Flow: 17 m³/h
Weight: 38, 42 kg

Cast iron submersible pump : High head Lifting of septic tanks, collective sanitary facilities and establishments receiving the public Exists in 5 versions Single-phase or three-phase Cast ...

GL series electric pumps, made of cast iron, are available with single-channel (GL) or vortex impeller (GLV). Designed to handle solids-laden wastewater, with up to 21 m head and 42 ...

PRODUCT FEATURES High efficiency pumps with ECM-technology and permanent magnet rotor Low power consumption EEI ≤0.18 Control modes: Proportional Pressure Constant Pressure Constand Speed Automatic “air purge” Plug Insulation ...

PRODUCT FEATURES High efficiency pumps with ECM-technology and permanent magnet rotor Low power consumption EEI ≤0.18 Stainless steel pump housing Control modes: Proportional Pressure Constant ...

... efficiency pumps with ECM-technology and permanent magnet rotor Low power consumption EEI ≤0.18 Control modes: Proportional Pressure Constant Pressure Constand Speed eAdapt Night Mode Automatic “air purge” Plug Reading ...

Features Installation: bare shaft Mechanical or magnetic clutch, monobloc Bronze impeller; Volute in cast iron or bronze. Q < 75 m3/h H < 50 m Applications Applications in industry, housing, agriculture, ...

... (MN) Based on (AN) In cast iron or in bronze Q < 500 – 700 m3/h H < 100 m High performance, low NPSH and high suction. Quiet operation. It can provide a vacuum system if the installation requirements require that ...

... Installation: bare shaft Based on In cast iron or in bronze Q < 2000 m3/h H < 30-150 m Design support based on double ball bearing in oil bath that gives great robustness and high reliability at the pump. Applications Fire ...

Features IN-LINE desing. In cast iron or in bronze Q < 140 m3/h H < 100 m Low NPSH, high performance and high suction. Applications Cooling, heating, air conditioning, etc.

... electric engine, diesel o gasoline, hydraulic or pneumatic On base, with flexible coupling-motor pump With mechanical or magnetic clutch In cast iron or in bronze Q < 300 m3/h H ...

Features Bare shaft or with electric engine. In cast iron or in bronze Q < 45 m3/h H < 225 m Multistage, providing high discharge pressures. For fluids clean and free of abrasive solids. Capacity of pumping liquids ...

Features Installation: bare shaft monobloc Based on Horizontal or vertical desing In bronze Intermediate variable length column. Q < 500 m3/h H < 30 m Ideal for fluids with high solids tenure. Applications BILGE fishing ...

Features Vertical desing. In bronze Flows up to 120 m3/h H < 4 bar (8 bar) DN 80 a 200 Temperatures < 80 °C Applications Marine Bilges

Features Aluminum casing corrosion resistant. Suction cover and cast iron GG25 impeller. Aluminum suction filter. Q < 180 m3/h H < 35 m Free passage 10 mm. High ...

Features Pump in cast iron or in bronze. Galvanized steel tank from 100 to 3000 liters capacity. Aluminum suction filter. Included gauge, pressure switch and keys ...

... Watertransport Technical data Q max 50.0 m³/h H max 22.5 m Design Vertical single-stage fully floodable submersible motor pumps in close-coupled design, IP68, with or without level control, max. immersion depth: ...

... Maintaining groundwater levels ▪ Draining of pits, shafts, etc. ▪ Building site drainage ▪ Construction pit drainage ▪ Emergency pump in the event of flooding Fluids handled Standard design ▪ Slightly contaminated ...

... max 40.0 m³/h H max 16.0 m Design Vertical single-stage fully floodable submersible waste water pump in close-coupled design (grey cast iron variant), non-explosion-proof. Application Handling ...

... treatment / 2.stage Biogas Breweries Building services Chemical industry Cooling water and condensate Drainage Drainage pump stations Energy Flood / stormwater holding tanks Flood control Flue gas desulphurization ...

... submersible motor pump for wet installation, with cutter (S), free-flow impeller (F) or diagonal single-vane impeller (D), stationary or transportable version. Amarex N pumps are floodable, single-stage, ...

... supply Water transport Technical data Q max 53.0 m³/h H max 52.0 m Design Horizontal, self-priming centrifugal pump in close-coupled design, open or semi-open impeller, adjusted via wear plate, with mechanical ...

... Water supply Water transport Technical data Q max 2,600.0 m³/h H max 160.0 m Design Multistage vertical turbine pump with closed impellers, column section with bearing assembly, shaft sleeve, shaft sealed ...

... industry Desalination Technical data Q max 4,800.0 m³/h H max 275.0 m Design Horizontal radially split volute casing pump in back pull-out design, with radial impeller, single-entry, single-stage, to ISO ...

... water Technical data Q max 468.0 m³/h H max 163.0 m Design Horizontal, long-coupled, single-stage volute casing pump in back pull-out design. Replaceable shaft protecting sleeves and casing wear rings. Applications Sprinkler ...

... engineering Oil /Gas Technical data Q max 980.0 m³/h H max 135.0 m Design Radially split vertical shaft submersible pump with double volute casing for wet and dry installation, with radial impeller, single-entry, ...

... ALPHA3, it’s never been quicker or easier to operate a pump within domestic heating systems. Through the Grundfos GO Remote app, the ALPHA3 is now controlled directly on your smartphone, making pump ...

... designed to work together seamlessly, no matter the application. The pumps are of the close-coupled type, with a mechanical shaft seal. The CMV pumps are available with cast-iron ...

... generation of CR pumps (CR 95, CR 125 and CR 155), offering an optimised hydraulic design for world-class energy efficiency. Thanks to a small footprint, the pumps are also easier and less costly to install ...

... hydraulically actuated piston diaphragm dosing pumps from 0.15 l/h up to 2 x 1500 l/h, with a pressure range from 200 to 4 bar General The Grundfos DMH range is a series of extremely strong, robust pumps ...

DWK and DPK are submersible pumps designed for dewatering and drainage applications. The cast-iron construction and the hydraulic design contribute durability and high efficiency. The ...

NBF is an end-suction pump made for fire sprinkler pump applications. NBF is a close-coupled type and NKF is a long-coupled type. The NKF fire system is an NBF or NKF end-suction pump ...

... control and communication is desired. The pump is ideal for larger development projects and is the perfect replacement for UPS pumps in existing systems. By adjusting the duty point to the actual heat ...

The MAGNA3/UPE pumps make up a broad range of small, medium and large circulator pumps – all fitted with communication equipment and state-of-the-art motors. These high performance pumps ...

... vertical in-line volute pumps are used in a variety of applications. The pumps are all single-stage, in-line centrifugal volute pumps with standard motors and mechanical shaft seals. ...

... want the pump to run at constant speed, or if you want an existing BMS system to control the pump. Being part of the TP-family, TPE3 and TPE2 pumps are of the close-coupled type, i.e. ...