- Products
- REPLIK
- Company
- Products
- Catalogs
- News & Trends
- Exhibitions
Parapet PARA2
Add to favorites
Compare this product
Description
Description
Parapet 70×42
BUSH‑HAMMERED STONE FINISH
Sales unit (U) = Unit
equivalence:
1U = 1 parapet
General information
Geometrical specifications (dimensions in cm)
length: 70
width: 42
thickness (cm): 15
weight (kg/U): 90
Mechanical properties
Splitting tensile strength (MPa): 5.2
Water absorption: < 6%
Frost/thaw (mass loss): 0.758 kg/m²
Slip resistance: average 62
Standards: NF – EN – 1340
Installation - Key recommendations
The indications provided by standard NF P 98 335 and the CCTG booklet 29 prevail.
– Install between +5°C and +30°C on a sound substrate.
– Mortars are prepared or supplied as work progresses.
– The bedding mortar layer must be leveled with a straightedge and applied progressively. Its thickness should be as uniform as possible (~4 cm).
– Slabs should be moistened, especially in hot conditions.
– When laying, blend products of different batches and shades to ensure visual uniformity across the installation.
– Joints are left between slabs. Joints are filled with mortar no sooner than 24 h and no later than 72 h after laying. Joint width should be as small as possible but not less than 5 mm.
– Immediately after jointing, clean the surface to avoid any residue or film on the slabs.
– Expansion joints shall be provided in accordance with normative requirements (10 lm or 20 m²).
Maintenance
– Products are designed to preserve surface appearance over time and require minimal maintenance.
– Applying a mineralizing treatment will facilitate maintenance and prolong the original aspect.
– Use of high‑pressure washers or acidic products is not recommended (risk of irreversible alteration).
– De‑icing salts should be used sparingly without leaving excess stagnant residues.
Colour range
A swatch of bush‑hammered stone finishes is available for colour selection.
Technical characteristics / specifications
Parapet 70×42
BUSH‑HAMMERED STONE FINISH
Sales unit (U) = Unit
equivalence:
1U = 1 parapet
General information
- Finish: bush‑hammered
- Packaging: 10 U/pallet (disposable pallet 110×90)
Geometrical specifications (dimensions in cm)
length: 70
width: 42
thickness (cm): 15
weight (kg/U): 90
Mechanical properties
Splitting tensile strength (MPa): 5.2
Water absorption: < 6%
Frost/thaw (mass loss): 0.758 kg/m²
Slip resistance: average 62
Standards: NF – EN – 1340
Installation - Key recommendations
The indications provided by standard NF P 98 335 and the CCTG booklet 29 prevail.
– Install between +5°C and +30°C on a sound substrate.
– Mortars are prepared or supplied as work progresses.
– The bedding mortar layer must be leveled with a straightedge and applied progressively. Its thickness should be as uniform as possible (~4 cm).
– Slabs should be moistened, especially in hot conditions.
– When laying, blend products of different batches and shades to ensure visual uniformity across the installation.
– Joints are left between slabs. Joints are filled with mortar no sooner than 24 h and no later than 72 h after laying. Joint width should be as small as possible but not less than 5 mm.
– Immediately after jointing, clean the surface to avoid any residue or film on the slabs.
– Expansion joints shall be provided in accordance with normative requirements (10 lm or 20 m²).
Maintenance
– Products are designed to preserve surface appearance over time and require minimal maintenance.
– Applying a mineralizing treatment will facilitate maintenance and prolong the original aspect.
– Use of high‑pressure washers or acidic products is not recommended (risk of irreversible alteration).
– De‑icing salts should be used sparingly without leaving excess stagnant residues.
Colour range
A swatch of bush‑hammered stone finishes is available for colour selection.
Technical characteristics / specifications
- Sales unit: Unit (1U = 1 parapet)
- Dimensions: 70 x 42 cm
- Thickness: 15 cm
- Weight: 90 kg per unit
- Packaging: 10 units per pallet (disposable pallet 110×90)
- Splitting tensile strength: 5.2 MPa
- Water absorption: < 6%
- Frost resistance (mass loss): 0.758 kg/m²
- Slip resistance: average 62
- Standard: NF – EN – 1340
Other REPLIK products
---
*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.